SecBSD/src
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
12ef7bd342
src/sys/dev/ic/atwreg.h
purplerain f57be82572
sync
2023-07-10 00:10:46 +00:00

1029 lines
40 KiB
C
Raw Blame History

/* $OpenBSD: atwreg.h,v 1.7 2009/08/16 18:03:48 jsg Exp $ */
/* $NetBSD: atwreg.h,v 1.10 2004/07/23 05:01:29 dyoung Exp $ */
/*
* Copyright (c) 2003 The NetBSD Foundation, Inc. All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by David Young.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY David Young AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL David Young
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
/* glossary */
/* DTIM Delivery Traffic Indication Map, sent by AP
* ATIM Ad Hoc Traffic Indication Map
* TU 1024 microseconds
* TSF time synchronization function
* TBTT target beacon transmission time
* DIFS distributed inter-frame space
* SIFS short inter-frame space
* EIFS extended inter-frame space
*/
/* Macros for bit twiddling. */
#ifndef _BIT_TWIDDLE
#define _BIT_TWIDDLE
/* find least significant bit that is set */
#define LOWEST_SET_BIT(x) ((((x) - 1) & (x)) ^ (x))
/* for x a power of two and p a non-negative integer, is x a greater power than 2**p? */
#define GTEQ_POWER(x, p) (((u_long)(x) >> (p)) != 0)
#define MASK_TO_SHIFT2(m) (GTEQ_POWER(LOWEST_SET_BIT((m)), 1) ? 1 : 0)
#define MASK_TO_SHIFT4(m) \
(GTEQ_POWER(LOWEST_SET_BIT((m)), 2) \
? 2 + MASK_TO_SHIFT2((m) >> 2) \
: MASK_TO_SHIFT2((m)))
#define MASK_TO_SHIFT8(m) \
(GTEQ_POWER(LOWEST_SET_BIT((m)), 4) \
? 4 + MASK_TO_SHIFT4((m) >> 4) \
: MASK_TO_SHIFT4((m)))
#define MASK_TO_SHIFT16(m) \
(GTEQ_POWER(LOWEST_SET_BIT((m)), 8) \
? 8 + MASK_TO_SHIFT8((m) >> 8) \
: MASK_TO_SHIFT8((m)))
#define MASK_TO_SHIFT(m) \
(GTEQ_POWER(LOWEST_SET_BIT((m)), 16) \
? 16 + MASK_TO_SHIFT16((m) >> 16) \
: MASK_TO_SHIFT16((m)))
#define MASK_AND_RSHIFT(x, mask) (((x) & (mask)) >> MASK_TO_SHIFT(mask))
#define LSHIFT(x, mask) ((x) << MASK_TO_SHIFT(mask))
#define MASK_AND_REPLACE(reg, val, mask) ((reg & ~mask) | LSHIFT(val, mask))
#define PRESHIFT(m) MASK_AND_RSHIFT((m), (m))
#endif /* _BIT_TWIDDLE */
/* ADM8211 Host Control and Status Registers */
#define ATW_PAR 0x00 /* PCI access */
#define ATW_FRCTL 0x04 /* Frame control */
#define ATW_TDR 0x08 /* Transmit demand */
#define ATW_WTDP 0x0C /* Current transmit descriptor pointer */
#define ATW_RDR 0x10 /* Receive demand */
#define ATW_WRDP 0x14 /* Current receive descriptor pointer */
#define ATW_RDB 0x18 /* Receive descriptor base address */
#define ATW_CSR3A 0x1C /* Unused (on ADM8211A) */
#define ATW_C_TDBH 0x1C /* Transmit descriptor base address,
* high-priority packet
*/
#define ATW_TDBD 0x20 /* Transmit descriptor base address, DCF */
#define ATW_TDBP 0x24 /* Transmit descriptor base address, PCF */
#define ATW_STSR 0x28 /* Status */
#define ATW_CSR5A 0x2C /* Unused */
#define ATW_C_TDBB 0x2C /* Transmit descriptor base address, buffered
* broadcast/multicast packet
*/
#define ATW_NAR 0x30 /* Network access */
#define ATW_CSR6A 0x34 /* Unused */
#define ATW_IER 0x38 /* Interrupt enable */
#define ATW_CSR7A 0x3C
#define ATW_LPC 0x40 /* Lost packet counter */
#define ATW_TEST1 0x44 /* Test register 1 */
#define ATW_SPR 0x48 /* Serial port */
#define ATW_TEST0 0x4C /* Test register 0 */
#define ATW_WCSR 0x50 /* Wake-up control/status */
#define ATW_WPDR 0x54 /* Wake-up pattern data */
#define ATW_GPTMR 0x58 /* General purpose timer */
#define ATW_GPIO 0x5C /* GPIO[5:0] configuration and control */
#define ATW_BBPCTL 0x60 /* BBP control port */
#define ATW_SYNCTL 0x64 /* synthesizer control port */
#define ATW_PLCPHD 0x68 /* PLCP header setting */
#define ATW_MMIWADDR 0x6C /* MMI write address */
#define ATW_MMIRADDR1 0x70 /* MMI read address 1 */
#define ATW_MMIRADDR2 0x74 /* MMI read address 2 */
#define ATW_TXBR 0x78 /* Transmit burst counter */
#define ATW_CSR15A 0x7C /* Unused */
#define ATW_ALCSTAT 0x80 /* ALC statistics */
#define ATW_TOFS2 0x84 /* Timing offset parameter 2, 16b */
#define ATW_CMDR 0x88 /* Command */
#define ATW_PCIC 0x8C /* PCI bus performance counter */
#define ATW_PMCSR 0x90 /* Power management command and status */
#define ATW_PAR0 0x94 /* Local MAC address register 0, 32b */
#define ATW_PAR1 0x98 /* Local MAC address register 1, 16b */
#define ATW_MAR0 0x9C /* Multicast address hash table register 0 */
#define ATW_MAR1 0xA0 /* Multicast address hash table register 1 */
#define ATW_ATIMDA0 0xA4 /* Ad Hoc Traffic Indication Map (ATIM)
* frame DA, byte[3:0]
*/
#define ATW_ABDA1 0xA8 /* BSSID address byte[5:4];
* ATIM frame DA byte[5:4]
*/
#define ATW_BSSID0 0xAC /* BSSID address byte[3:0] */
#define ATW_TXLMT 0xB0 /* WLAN retry limit, 8b;
* Max TX MSDU lifetime, 16b
*/
#define ATW_MIBCNT 0xB4 /* RTS/ACK/FCS MIB count, 32b */
#define ATW_BCNT 0xB8 /* Beacon transmission time, 32b */
#define ATW_TSFTH 0xBC /* TSFT[63:32], 32b */
#define ATW_TSC 0xC0 /* TSFT[39:32] down count value */
#define ATW_SYNRF 0xC4 /* SYN RF IF direct control */
#define ATW_BPLI 0xC8 /* Beacon interval, 16b.
* STA listen interval, 16b.
*/
#define ATW_CAP0 0xCC /* Current channel, 4b. RCVDTIM, 1b. */
#define ATW_CAP1 0xD0 /* Capability information, 16b.
* ATIM window, 1b.
*/
#define ATW_RMD 0xD4 /* RX max reception duration, 16b */
#define ATW_CFPP 0xD8 /* CFP parameter, 32b */
#define ATW_TOFS0 0xDC /* Timing offset parameter 0, 28b */
#define ATW_TOFS1 0xE0 /* Timing offset parameter 1, 24b */
#define ATW_IFST 0xE4 /* IFS timing parameter 1, 32b */
#define ATW_RSPT 0xE8 /* Response time, 24b */
#define ATW_TSFTL 0xEC /* TSFT[31:0], 32b */
#define ATW_WEPCTL 0xF0 /* WEP control */
#define ATW_WESK 0xF4 /* Write entry for shared/individual key */
#define ATW_WEPCNT 0xF8 /* WEP count */
#define ATW_MACTEST 0xFC
#define ATW_FER 0x100 /* Function event */
#define ATW_FEMR 0x104 /* Function event mask */
#define ATW_FPSR 0x108 /* Function present state */
#define ATW_FFER 0x10C /* Function force event */
#define ATW_PAR_MWIE (1<<24) /* memory write and invalidate
* enable
*/
#define ATW_PAR_MRLE (1<<23) /* memory read line enable */
#define ATW_PAR_MRME (1<<21) /* memory read multiple
* enable
*/
#define ATW_PAR_RAP_MASK 0x60000 /* receive auto-polling in
* receive suspended state
*/
#define ATW_PAR_CAL_MASK 0xc000 /* cache alignment */
#define ATW_PAR_CAL_PBL 0x0
/* min(8 DW, PBL) */
#define ATW_PAR_CAL_8DW LSHIFT(0x1, ATW_PAR_CAL_MASK)
/* min(16 DW, PBL) */
#define ATW_PAR_CAL_16DW LSHIFT(0x2, ATW_PAR_CAL_MASK)
/* min(32 DW, PBL) */
#define ATW_PAR_CAL_32DW LSHIFT(0x3, ATW_PAR_CAL_MASK)
#define ATW_PAR_PBL_MASK 0x3f00 /* programmable burst length */
#define ATW_PAR_PBL_UNLIMITED 0x0
#define ATW_PAR_PBL_1DW LSHIFT(0x1, ATW_PAR_PBL_MASK)
#define ATW_PAR_PBL_2DW LSHIFT(0x2, ATW_PAR_PBL_MASK)
#define ATW_PAR_PBL_4DW LSHIFT(0x4, ATW_PAR_PBL_MASK)
#define ATW_PAR_PBL_8DW LSHIFT(0x8, ATW_PAR_PBL_MASK)
#define ATW_PAR_PBL_16DW LSHIFT(0x16, ATW_PAR_PBL_MASK)
#define ATW_PAR_PBL_32DW LSHIFT(0x32, ATW_PAR_PBL_MASK)
#define ATW_PAR_BLE (1<<7) /* big/little endian selection */
#define ATW_PAR_DSL_MASK 0x7c /* descriptor skip length */
#define ATW_PAR_BAR (1<<1) /* bus arbitration */
#define ATW_PAR_SWR (1<<0) /* software reset */
#define ATW_FRCTL_PWRMGMT (1<<31) /* power management */
#define ATW_FRCTL_VER_MASK 0x60000000 /* protocol version */
#define ATW_FRCTL_ORDER (1<<28) /* order bit */
#define ATW_FRCTL_MAXPSP (1<<27) /* maximum power saving */
#define ATW_C_FRCTL_PRSP (1<<26) /* 1: driver sends probe
* response
* 0: ASIC sends prresp
*/
#define ATW_C_FRCTL_DRVBCON (1<<25) /* 1: driver sends beacons
* 0: ASIC sends beacons
*/
#define ATW_C_FRCTL_DRVLINKCTRL (1<<24) /* 1: driver controls link LED
* 0: ASIC controls link LED
*/
#define ATW_C_FRCTL_DRVLINKON (1<<23) /* 1: turn on link LED
* 0: turn off link LED
*/
#define ATW_C_FRCTL_CTX_DATA (1<<22) /* 0: set by CSR28
* 1: random
*/
#define ATW_C_FRCTL_RSVFRM (1<<21) /* 1: receive "reserved"
* frames, 0: ignore
* reserved frames
*/
#define ATW_C_FRCTL_CFEND (1<<19) /* write to send CF_END,
* ADM8211C/CR clears
*/
#define ATW_FRCTL_DOZEFRM (1<<18) /* select pre-sleep frame */
#define ATW_FRCTL_PSAWAKE (1<<17) /* MAC is awake (?) */
#define ATW_FRCTL_PSMODE (1<<16) /* MAC is power-saving (?) */
#define ATW_FRCTL_AID_MASK 0xffff /* STA Association ID */
#define ATW_INTR_PCF (1<<31) /* started/ended CFP */
#define ATW_INTR_BCNTC (1<<30) /* transmitted IBSS beacon */
#define ATW_INTR_GPINT (1<<29) /* GPIO interrupt */
#define ATW_INTR_LINKOFF (1<<28) /* lost ATW_WCSR_BLN beacons */
#define ATW_INTR_ATIMTC (1<<27) /* transmitted ATIM */
#define ATW_INTR_TSFTF (1<<26) /* TSFT out of range */
#define ATW_INTR_TSCZ (1<<25) /* TSC countdown expired */
#define ATW_INTR_LINKON (1<<24) /* matched SSID, BSSID */
#define ATW_INTR_SQL (1<<23) /* Marvel signal quality */
#define ATW_INTR_WEPTD (1<<22) /* switched WEP table */
#define ATW_INTR_ATIME (1<<21) /* ended ATIM window */
#define ATW_INTR_TBTT (1<<20) /* (TBTT) Target Beacon TX Time
* passed
*/
#define ATW_INTR_NISS (1<<16) /* normal interrupt status
* summary: any of 31, 30, 27,
* 24, 14, 12, 6, 2, 0.
*/
#define ATW_INTR_AISS (1<<15) /* abnormal interrupt status
* summary: any of 29, 28, 26,
* 25, 23, 22, 13, 11, 8, 7, 5,
* 4, 3, 1.
*/
#define ATW_INTR_TEIS (1<<14) /* transmit early interrupt
* status: moved TX packet to
* FIFO
*/
#define ATW_INTR_FBE (1<<13) /* fatal bus error */
#define ATW_INTR_REIS (1<<12) /* receive early interrupt
* status: RX packet filled
* its first descriptor
*/
#define ATW_INTR_GPTT (1<<11) /* general purpose timer expired */
#define ATW_INTR_RPS (1<<8) /* stopped receive process */
#define ATW_INTR_RDU (1<<7) /* receive descriptor
* unavailable
*/
#define ATW_INTR_RCI (1<<6) /* completed packet reception */
#define ATW_INTR_TUF (1<<5) /* transmit underflow */
#define ATW_INTR_TRT (1<<4) /* transmit retry count
* expired
*/
#define ATW_INTR_TLT (1<<3) /* transmit lifetime exceeded */
#define ATW_INTR_TDU (1<<2) /* transmit descriptor
* unavailable
*/
#define ATW_INTR_TPS (1<<1) /* stopped transmit process */
#define ATW_INTR_TCI (1<<0) /* completed transmit */
#define ATW_NAR_TXCF (1<<31) /* stop process on TX failure */
#define ATW_NAR_HF (1<<30) /* flush TX FIFO to host (?) */
#define ATW_NAR_UTR (1<<29) /* select retry count source */
#define ATW_NAR_PCF (1<<28) /* use one/both transmit
* descriptor base addresses
*/
#define ATW_NAR_CFP (1<<27) /* indicate more TX data to
* point coordinator
*/
#define ATW_C_NAR_APSTA (1<<26) /* 0: STA mode
* 1: AP mode
*/
#define ATW_C_NAR_TDBBE (1<<25) /* 0: disable TDBB
* 1: enable TDBB
*/
#define ATW_C_NAR_TDBHE (1<<24) /* 0: disable TDBH
* 1: enable TDBH
*/
#define ATW_C_NAR_TDBHT (1<<23) /* write 1 to make ASIC
* poll TDBH once; ASIC clears
*/
#define ATW_NAR_SF (1<<21) /* store and forward: ignore
* TX threshold
*/
#define ATW_NAR_TR_MASK 0xc000 /* TX threshold */
#define ATW_NAR_TR_L64 LSHIFT(0x0, ATW_NAR_TR_MASK)
#define ATW_NAR_TR_L160 LSHIFT(0x2, ATW_NAR_TR_MASK)
#define ATW_NAR_TR_L192 LSHIFT(0x3, ATW_NAR_TR_MASK)
#define ATW_NAR_TR_H96 LSHIFT(0x0, ATW_NAR_TR_MASK)
#define ATW_NAR_TR_H288 LSHIFT(0x2, ATW_NAR_TR_MASK)
#define ATW_NAR_TR_H544 LSHIFT(0x3, ATW_NAR_TR_MASK)
#define ATW_NAR_ST (1<<13) /* start/stop transmit */
#define ATW_NAR_OM_MASK 0xc00 /* operating mode */
#define ATW_NAR_OM_NORMAL 0x0
#define ATW_NAR_OM_LOOPBACK LSHIFT(0x1, ATW_NAR_OM_MASK)
#define ATW_NAR_MM (1<<7) /* RX any multicast */
#define ATW_NAR_PR (1<<6) /* promiscuous mode */
#define ATW_NAR_EA (1<<5) /* match ad hoc packets (?) */
#define ATW_NAR_DISPCF (1<<4) /* 1: PCF *not* supported
* 0: PCF supported
*/
#define ATW_NAR_PB (1<<3) /* pass bad packets */
#define ATW_NAR_STPDMA (1<<2) /* stop DMA, abort packet */
#define ATW_NAR_SR (1<<1) /* start/stop receive */
#define ATW_NAR_CTX (1<<0) /* continuous TX mode */
/* IER bits are identical to STSR bits. Use ATW_INTR_*. */
#if 0
#define ATW_IER_NIE (1<<16) /* normal interrupt enable */
#define ATW_IER_AIE (1<<15) /* abnormal interrupt enable */
/* normal interrupts: combine with ATW_IER_NIE */
#define ATW_IER_PCFIE (1<<31) /* STA entered CFP */
#define ATW_IER_BCNTCIE (1<<30) /* STA TX'd beacon */
#define ATW_IER_ATIMTCIE (1<<27) /* transmitted ATIM */
#define ATW_IER_LINKONIE (1<<24) /* matched beacon */
#define ATW_IER_ATIMIE (1<<21) /* ended ATIM window */
#define ATW_IER_TBTTIE (1<<20) /* TBTT */
#define ATW_IER_TEIE (1<<14) /* moved TX packet to FIFO */
#define ATW_IER_REIE (1<<12) /* RX packet filled its first
* descriptor
*/
#define ATW_IER_RCIE (1<<6) /* completed RX */
#define ATW_IER_TDUIE (1<<2) /* transmit descriptor
* unavailable
*/
#define ATW_IER_TCIE (1<<0) /* completed TX */
/* abnormal interrupts: combine with ATW_IER_AIE */
#define ATW_IER_GPIE (1<<29) /* GPIO interrupt */
#define ATW_IER_LINKOFFIE (1<<28) /* lost beacon */
#define ATW_IER_TSFTFIE (1<<26) /* TSFT out of range */
#define ATW_IER_TSCIE (1<<25) /* TSC countdown expired */
#define ATW_IER_SQLIE (1<<23) /* signal quality */
#define ATW_IER_WEPIE (1<<22) /* finished WEP table switch */
#define ATW_IER_FBEIE (1<<13) /* fatal bus error */
#define ATW_IER_GPTIE (1<<11) /* general purpose timer expired */
#define ATW_IER_RPSIE (1<<8) /* stopped receive process */
#define ATW_IER_RUIE (1<<7) /* receive descriptor unavailable */
#define ATW_IER_TUIE (1<<5) /* transmit underflow */
#define ATW_IER_TRTIE (1<<4) /* exceeded transmit retry count */
#define ATW_IER_TLTTIE (1<<3) /* transmit lifetime exceeded */
#define ATW_IER_TPSIE (1<<1) /* stopped transmit process */
#endif
#define ATW_LPC_LPCO (1<<16) /* lost packet counter overflow */
#define ATW_LPC_LPC_MASK 0xffff /* lost packet counter */
#define ATW_TEST1_CONTROL (1<<31) /* "0: read from dxfer_control,
* 1: read from dxfer_state"
*/
#define ATW_TEST1_DBGREAD_MASK 0x70000000 /* "control of read data,
* debug only"
*/
#define ATW_TEST1_TXWP_MASK 0xe000000 /* select ATW_WTDP content? */
#define ATW_TEST1_TXWP_TDBD LSHIFT(0x0, ATW_TEST1_TXWP_MASK)
#define ATW_TEST1_TXWP_TDBH LSHIFT(0x1, ATW_TEST1_TXWP_MASK)
#define ATW_TEST1_TXWP_TDBB LSHIFT(0x2, ATW_TEST1_TXWP_MASK)
#define ATW_TEST1_TXWP_TDBP LSHIFT(0x3, ATW_TEST1_TXWP_MASK)
#define ATW_TEST1_RSVD0_MASK 0x1ffffc0 /* reserved */
#define ATW_TEST1_TESTMODE_MASK 0x30
/* normal operation */
#define ATW_TEST1_TESTMODE_NORMAL LSHIFT(0x0, ATW_TEST1_TESTMODE_MASK)
/* MAC-only mode */
#define ATW_TEST1_TESTMODE_MACONLY LSHIFT(0x1, ATW_TEST1_TESTMODE_MASK)
/* normal operation */
#define ATW_TEST1_TESTMODE_NORMAL2 LSHIFT(0x2, ATW_TEST1_TESTMODE_MASK)
/* monitor mode */
#define ATW_TEST1_TESTMODE_MONITOR LSHIFT(0x3, ATW_TEST1_TESTMODE_MASK)
#define ATW_TEST1_DUMP_MASK 0xf /* select dump signal
* from dxfer (huh?)
*/
#define ATW_SPR_SRS (1<<11) /* activate SEEPROM access */
#define ATW_SPR_SDO (1<<3) /* data out of SEEPROM */
#define ATW_SPR_SDI (1<<2) /* data into SEEPROM */
#define ATW_SPR_SCLK (1<<1) /* SEEPROM clock */
#define ATW_SPR_SCS (1<<0) /* SEEPROM chip select */
#define ATW_TEST0_BE_MASK 0xe0000000 /* Bus error state */
#define ATW_TEST0_TS_MASK 0x1c000000 /* Transmit process state */
/* Stopped */
#define ATW_TEST0_TS_STOPPED LSHIFT(0, ATW_TEST0_TS_MASK)
/* Running - fetch transmit descriptor */
#define ATW_TEST0_TS_FETCH LSHIFT(1, ATW_TEST0_TS_MASK)
/* Running - wait for end of transmission */
#define ATW_TEST0_TS_WAIT LSHIFT(2, ATW_TEST0_TS_MASK)
/* Running - read buffer from memory and queue into FIFO */
#define ATW_TEST0_TS_READING LSHIFT(3, ATW_TEST0_TS_MASK)
#define ATW_TEST0_TS_RESERVED1 LSHIFT(4, ATW_TEST0_TS_MASK)
#define ATW_TEST0_TS_RESERVED2 LSHIFT(5, ATW_TEST0_TS_MASK)
/* Suspended */
#define ATW_TEST0_TS_SUSPENDED LSHIFT(6, ATW_TEST0_TS_MASK)
/* Running - close transmit descriptor */
#define ATW_TEST0_TS_CLOSE LSHIFT(7, ATW_TEST0_TS_MASK)
/* ADM8211C/CR registers */
/* Suspended */
#define ATW_C_TEST0_TS_SUSPENDED LSHIFT(4, ATW_TEST0_TS_MASK)
/* Descriptor write */
#define ATW_C_TEST0_TS_CLOSE LSHIFT(5, ATW_TEST0_TS_MASK)
/* Last descriptor write */
#define ATW_C_TEST0_TS_CLOSELAST LSHIFT(6, ATW_TEST0_TS_MASK)
/* FIFO full */
#define ATW_C_TEST0_TS_FIFOFULL LSHIFT(7, ATW_TEST0_TS_MASK)
#define ATW_TEST0_RS_MASK 0x3800000 /* Receive process state */
/* Stopped */
#define ATW_TEST0_RS_STOPPED LSHIFT(0, ATW_TEST0_RS_MASK)
/* Running - fetch receive descriptor */
#define ATW_TEST0_RS_FETCH LSHIFT(1, ATW_TEST0_RS_MASK)
/* Running - check for end of receive */
#define ATW_TEST0_RS_CHECK LSHIFT(2, ATW_TEST0_RS_MASK)
/* Running - wait for packet */
#define ATW_TEST0_RS_WAIT LSHIFT(3, ATW_TEST0_RS_MASK)
/* Suspended */
#define ATW_TEST0_RS_SUSPENDED LSHIFT(4, ATW_TEST0_RS_MASK)
/* Running - close receive descriptor */
#define ATW_TEST0_RS_CLOSE LSHIFT(5, ATW_TEST0_RS_MASK)
/* Running - flush current frame from FIFO */
#define ATW_TEST0_RS_FLUSH LSHIFT(6, ATW_TEST0_RS_MASK)
/* Running - queue current frame from FIFO into buffer */
#define ATW_TEST0_RS_QUEUE LSHIFT(7, ATW_TEST0_RS_MASK)
#define ATW_TEST0_EPNE (1<<18) /* SEEPROM not detected */
#define ATW_TEST0_EPSNM (1<<17) /* SEEPROM bad signature */
#define ATW_TEST0_EPTYP_MASK (1<<16) /* SEEPROM type
* 1: 93c66,
* 0: 93c46
*/
#define ATW_TEST0_EPTYP_93c66 ATW_TEST0_EPTYP_MASK
#define ATW_TEST0_EPTYP_93c46 0
#define ATW_TEST0_EPRLD (1<<15) /* recall SEEPROM (write 1) */
#define ATW_WCSR_CRCT (1<<30) /* CRC-16 type */
#define ATW_WCSR_WP1E (1<<29) /* match wake-up pattern 1 */
#define ATW_WCSR_WP2E (1<<28) /* match wake-up pattern 2 */
#define ATW_WCSR_WP3E (1<<27) /* match wake-up pattern 3 */
#define ATW_WCSR_WP4E (1<<26) /* match wake-up pattern 4 */
#define ATW_WCSR_WP5E (1<<25) /* match wake-up pattern 5 */
#define ATW_WCSR_BLN_MASK 0xe00000 /* lose link after BLN lost
* beacons
*/
#define ATW_WCSR_TSFTWE (1<<20) /* wake up on TSFT out of
* range
*/
#define ATW_WCSR_TIMWE (1<<19) /* wake up on TIM */
#define ATW_WCSR_ATIMWE (1<<18) /* wake up on ATIM */
#define ATW_WCSR_KEYWE (1<<17) /* wake up on key update */
#define ATW_WCSR_WFRE (1<<10) /* wake up on wake-up frame */
#define ATW_WCSR_MPRE (1<<9) /* wake up on magic packet */
#define ATW_WCSR_LSOE (1<<8) /* wake up on link loss */
/* wake-up reasons correspond to enable bits */
#define ATW_WCSR_KEYUP (1<<6) /* */
#define ATW_WCSR_TSFTW (1<<5) /* */
#define ATW_WCSR_TIMW (1<<4) /* */
#define ATW_WCSR_ATIMW (1<<3) /* */
#define ATW_WCSR_WFR (1<<2) /* */
#define ATW_WCSR_MPR (1<<1) /* */
#define ATW_WCSR_LSO (1<<0) /* */
#define ATW_GPTMR_COM_MASK (1<<16) /* continuous operation mode */
#define ATW_GPTMR_GTV_MASK 0xffff /* set countdown in 204us ticks */
#define ATW_GPIO_EC1_MASK 0x3000000 /* GPIO1 event configuration */
#define ATW_GPIO_LAT_MASK 0x300000 /* input latch */
#define ATW_GPIO_INTEN_MASK 0xc0000 /* interrupt enable */
#define ATW_GPIO_EN_MASK 0x3f000 /* output enable */
#define ATW_GPIO_O_MASK 0xfc0 /* output value */
#define ATW_GPIO_I_MASK 0x3f /* pin static input */
#define ATW_BBPCTL_TWI (1<<31) /* Intersil 3-wire interface */
#define ATW_BBPCTL_RF3KADDR_MASK 0x7f000000 /* Address for RF3000 */
#define ATW_BBPCTL_RF3KADDR_ADDR LSHIFT(0x20, ATW_BBPCTL_RF3KADDR_MASK)
#define ATW_BBPCTL_NEGEDGE_DO (1<<23) /* data-out on negative edge */
#define ATW_BBPCTL_NEGEDGE_DI (1<<22) /* data-in on negative edge */
#define ATW_BBPCTL_CCA_ACTLO (1<<21) /* CCA low when busy */
#define ATW_BBPCTL_TYPE_MASK 0x1c0000 /* BBP type */
#define ATW_BBPCTL_WR (1<<17) /* start write; reset on
* completion
*/
#define ATW_BBPCTL_RD (1<<16) /* start read; reset on
* completion
*/
#define ATW_BBPCTL_ADDR_MASK 0xff00 /* BBP address */
#define ATW_BBPCTL_DATA_MASK 0xff /* BBP data */
#define ATW_SYNCTL_WR (1<<31) /* start write; reset on
* completion
*/
#define ATW_SYNCTL_RD (1<<30) /* start read; reset on
* completion
*/
#define ATW_SYNCTL_CS0 (1<<29) /* chip select */
#define ATW_SYNCTL_CS1 (1<<28)
#define ATW_SYNCTL_CAL (1<<27) /* generate RF CAL pulse after
* Rx
*/
#define ATW_SYNCTL_SELCAL (1<<26) /* RF CAL source, 0: CAL bit,
* 1: MAC; needed by Intersil
* BBP
*/
#define ATW_C_SYNCTL_MMICE (1<<25) /* ADM8211C/CR define this
* bit. 0: latch data on
* negative edge, 1: positive
* edge.
*/
#define ATW_SYNCTL_RFTYPE_MASK 0x1c00000 /* RF type */
#define ATW_SYNCTL_DATA_MASK 0x3fffff /* synthesizer setting */
#define ATW_PLCPHD_SIGNAL_MASK 0xff000000 /* signal field in PLCP header,
* only for beacon, ATIM, and
* RTS.
*/
#define ATW_PLCPHD_SERVICE_MASK 0xff0000 /* service field in PLCP
* header; with RFMD BBP,
* sets Tx power for beacon,
* RTS, ATIM.
*/
#define ATW_PLCPHD_PMBL (1<<15) /* 0: long preamble, 1: short */
#define ATW_MMIWADDR_LENLO_MASK 0xff000000 /* tx: written 4th */
#define ATW_MMIWADDR_LENHI_MASK 0xff0000 /* tx: written 3rd */
#define ATW_MMIWADDR_GAIN_MASK 0xff00 /* tx: written 2nd */
#define ATW_MMIWADDR_RATE_MASK 0xff /* tx: written 1st */
/* was magic 0x100E0C0A */
#define ATW_MMIWADDR_INTERSIL \
(LSHIFT(0x0c, ATW_MMIWADDR_GAIN_MASK) | \
LSHIFT(0x0a, ATW_MMIWADDR_RATE_MASK) | \
LSHIFT(0x0e, ATW_MMIWADDR_LENHI_MASK) | \
LSHIFT(0x10, ATW_MMIWADDR_LENLO_MASK))
/* was magic 0x00009101
*
* ADMtek sets the AI bit on the ATW_MMIWADDR_GAIN_MASK address to
* put the RF3000 into auto-increment mode so that it can write Tx gain,
* Tx length (high) and Tx length (low) registers back-to-back.
*/
#define ATW_MMIWADDR_RFMD \
(LSHIFT(RF3000_TWI_AI|RF3000_GAINCTL, ATW_MMIWADDR_GAIN_MASK) | \
LSHIFT(RF3000_CTL, ATW_MMIWADDR_RATE_MASK))
#define ATW_MMIRADDR1_RSVD_MASK 0xff000000
#define ATW_MMIRADDR1_PWRLVL_MASK 0xff0000
#define ATW_MMIRADDR1_RSSI_MASK 0xff00
#define ATW_MMIRADDR1_RXSTAT_MASK 0xff
/* was magic 0x00007c7e
*
* TBD document registers for Intersil 3861 baseband
*/
#define ATW_MMIRADDR1_INTERSIL \
(LSHIFT(0x7c, ATW_MMIRADDR1_RSSI_MASK) | \
LSHIFT(0x7e, ATW_MMIRADDR1_RXSTAT_MASK))
/* was magic 0x00000301 */
#define ATW_MMIRADDR1_RFMD \
(LSHIFT(RF3000_RSSI, ATW_MMIRADDR1_RSSI_MASK) | \
LSHIFT(RF3000_RXSTAT, ATW_MMIRADDR1_RXSTAT_MASK))
/* was magic 0x00100000 */
#define ATW_MMIRADDR2_INTERSIL \
(LSHIFT(0x0, ATW_MMIRADDR2_ID_MASK) | \
LSHIFT(0x10, ATW_MMIRADDR2_RXPECNT_MASK))
/* was magic 0x7e100000 */
#define ATW_MMIRADDR2_RFMD \
(LSHIFT(0x7e, ATW_MMIRADDR2_ID_MASK) | \
LSHIFT(0x10, ATW_MMIRADDR2_RXPECNT_MASK))
#define ATW_MMIRADDR2_ID_MASK 0xff000000 /* 1st element ID in WEP table
* for Probe Response (huh?)
*/
/* RXPE is re-asserted after RXPECNT * 22MHz. */
#define ATW_MMIRADDR2_RXPECNT_MASK 0xff0000
#define ATW_MMIRADDR2_PROREXT (1<<15) /* Probe Response
* 11Mb/s length
* extension.
*/
#define ATW_MMIRADDR2_PRORLEN_MASK 0x7fff /* Probe Response
* microsecond length
*/
#define ATW_TXBR_ALCUPDATE_MASK (1<<31) /* auto-update BBP with ALCSET */
#define ATW_TXBR_TBCNT_MASK 0x1f0000 /* transmit burst count */
#define ATW_TXBR_ALCSET_MASK 0xff00 /* TX power level set point */
#define ATW_TXBR_ALCREF_MASK 0xff /* TX power level reference point */
#define ATW_ALCSTAT_MCOV_MASK (1<<27) /* MPDU count overflow */
#define ATW_ALCSTAT_ESOV_MASK (1<<26) /* error sum overflow */
#define ATW_ALCSTAT_MCNT_MASK 0x3ff0000 /* MPDU count, unsigned integer */
#define ATW_ALCSTAT_ERSUM_MASK 0xffff /* power error sum,
* 2's complement signed integer
*/
#define ATW_TOFS2_PWR1UP_MASK 0xf0000000 /* delay of Tx/Rx from PE1,
* Radio, PHYRST change after
* power-up, in 2ms units
*/
#define ATW_TOFS2_PWR0PAPE_MASK 0xf000000 /* delay of PAPE going low
* after internal data
* transmit end, in us
*/
#define ATW_TOFS2_PWR1PAPE_MASK 0xf00000 /* delay of PAPE going high
* after TXPE asserted, in us
*/
#define ATW_TOFS2_PWR0TRSW_MASK 0xf0000 /* delay of TRSW going low
* after internal data transmit
* end, in us
*/
#define ATW_TOFS2_PWR1TRSW_MASK 0xf000 /* delay of TRSW going high
* after TXPE asserted, in us
*/
#define ATW_TOFS2_PWR0PE2_MASK 0xf00 /* delay of PE2 going low
* after internal data transmit
* end, in us
*/
#define ATW_TOFS2_PWR1PE2_MASK 0xf0 /* delay of PE2 going high
* after TXPE asserted, in us
*/
#define ATW_TOFS2_PWR0TXPE_MASK 0xf /* delay of TXPE going low
* after internal data transmit
* end, in us
*/
#define ATW_CMDR_PM (1<<19) /* enables power mgmt
* capabilities.
*/
#define ATW_CMDR_APM (1<<18) /* APM mode, effective when
* PM = 1.
*/
#define ATW_CMDR_RTE (1<<4) /* enable Rx FIFO threshold */
#define ATW_CMDR_DRT_MASK 0xc /* drain Rx FIFO threshold */
/* 32 bytes */
#define ATW_CMDR_DRT_8DW LSHIFT(0x0, ATW_CMDR_DRT_MASK)
/* 64 bytes */
#define ATW_CMDR_DRT_16DW LSHIFT(0x1, ATW_CMDR_DRT_MASK)
/* Store & Forward */
#define ATW_CMDR_DRT_SF LSHIFT(0x2, ATW_CMDR_DRT_MASK)
/* Reserved */
#define ATW_CMDR_DRT_RSVD LSHIFT(0x3, ATW_CMDR_DRT_MASK)
#define ATW_CMDR_SINT_MASK (1<<1) /* software interrupt---huh? */
/* TBD PCIC */
/* TBD PMCSR */
#define ATW_PAR0_PAB0_MASK 0xff /* MAC address byte 0 */
#define ATW_PAR0_PAB1_MASK 0xff00 /* MAC address byte 1 */
#define ATW_PAR0_PAB2_MASK 0xff0000 /* MAC address byte 2 */
#define ATW_PAR0_PAB3_MASK 0xff000000 /* MAC address byte 3 */
#define ATW_C_PAR1_CTD 0xffff0000 /* Continuous Tx pattern */
#define ATW_PAR1_PAB5_MASK 0xff00 /* MAC address byte 5 */
#define ATW_PAR1_PAB4_MASK 0xff /* MAC address byte 4 */
#define ATW_MAR0_MAB3_MASK 0xff000000 /* multicast table bits 31:24 */
#define ATW_MAR0_MAB2_MASK 0xff0000 /* multicast table bits 23:16 */
#define ATW_MAR0_MAB1_MASK 0xff00 /* multicast table bits 15:8 */
#define ATW_MAR0_MAB0_MASK 0xff /* multicast table bits 7:0 */
#define ATW_MAR1_MAB7_MASK 0xff000000 /* multicast table bits 63:56 */
#define ATW_MAR1_MAB6_MASK 0xff0000 /* multicast table bits 55:48 */
#define ATW_MAR1_MAB5_MASK 0xff00 /* multicast table bits 47:40 */
#define ATW_MAR1_MAB4_MASK 0xff /* multicast table bits 39:32 */
/* ATIM destination address */
#define ATW_ATIMDA0_ATIMB3_MASK 0xff000000
#define ATW_ATIMDA0_ATIMB2_MASK 0xff0000
#define ATW_ATIMDA0_ATIMB1_MASK 0xff00
#define ATW_ATIMDA0_ATIMB0_MASK 0xff
/* ATIM destination address, BSSID */
#define ATW_ABDA1_BSSIDB5_MASK 0xff000000
#define ATW_ABDA1_BSSIDB4_MASK 0xff0000
#define ATW_ABDA1_ATIMB5_MASK 0xff00
#define ATW_ABDA1_ATIMB4_MASK 0xff
/* BSSID */
#define ATW_BSSID0_BSSIDB3_MASK 0xff000000
#define ATW_BSSID0_BSSIDB2_MASK 0xff0000
#define ATW_BSSID0_BSSIDB1_MASK 0xff00
#define ATW_BSSID0_BSSIDB0_MASK 0xff
#define ATW_TXLMT_MTMLT_MASK 0xffff0000 /* max TX MSDU lifetime in TU */
#define ATW_TXLMT_SRTYLIM_MASK 0xff /* short retry limit */
#define ATW_MIBCNT_FFCNT_MASK 0xff000000 /* FCS failure count */
#define ATW_MIBCNT_AFCNT_MASK 0xff0000 /* ACK failure count */
#define ATW_MIBCNT_RSCNT_MASK 0xff00 /* RTS success count */
#define ATW_MIBCNT_RFCNT_MASK 0xff /* RTS failure count */
#define ATW_BCNT_PLCPH_MASK 0xff0000 /* 11M PLCP length (us) */
#define ATW_BCNT_PLCPL_MASK 0xff00 /* 5.5M PLCP length (us) */
#define ATW_BCNT_BCNT_MASK 0xff /* byte count of beacon frame */
/* For ADM8211C/CR */
/* ATW_C_TSC_TIMTABSEL = 1 */
#define ATW_C_BCNT_EXTEN1 (1<<31) /* 11M beacon len. extension */
#define ATW_C_BCNT_BEANLEN1 0x7fff0000 /* beacon length in us */
/* ATW_C_TSC_TIMTABSEL = 0 */
#define ATW_C_BCNT_EXTEN0 (1<<15) /* 11M beacon len. extension */
#define ATW_C_BCNT_BEANLEN0 BIT(14,0) /* beacon length in us */
#define ATW_C_TSC_TIMOFS 0xff000000 /* I think this is the
* SRAM offset for the TIM
*/
#define ATW_C_TSC_TIMLEN 0x3ff000 /* length of TIM */
#define ATW_C_TSC_TIMTABSEL (1<<4) /* select TIM table 0 or 1 */
#define ATW_TSC_TSC_MASK 0xf /* TSFT countdown value, 0
* disables
*/
#define ATW_SYNRF_SELSYN (1<<31) /* 0: MAC controls SYN IF pins,
* 1: ATW_SYNRF controls SYN IF pins.
*/
#define ATW_SYNRF_SELRF (1<<30) /* 0: MAC controls RF IF pins,
* 1: ATW_SYNRF controls RF IF pins.
*/
#define ATW_SYNRF_LERF (1<<29) /* if SELSYN = 1, direct control of
* LERF# pin
*/
#define ATW_SYNRF_LEIF (1<<28) /* if SELSYN = 1, direct control of
* LEIF# pin
*/
#define ATW_SYNRF_SYNCLK (1<<27) /* if SELSYN = 1, direct control of
* SYNCLK pin
*/
#define ATW_SYNRF_SYNDATA (1<<26) /* if SELSYN = 1, direct control of
* SYNDATA pin
*/
#define ATW_SYNRF_PE1 (1<<25) /* if SELRF = 1, direct control of
* PE1 pin
*/
#define ATW_SYNRF_PE2 (1<<24) /* if SELRF = 1, direct control of
* PE2 pin
*/
#define ATW_SYNRF_PAPE (1<<23) /* if SELRF = 1, direct control of
* PAPE pin
*/
#define ATW_C_SYNRF_TRSW (1<<22) /* if SELRF = 1, direct control of
* TRSW pin
*/
#define ATW_C_SYNRF_TRSWN (1<<21) /* if SELRF = 1, direct control of
* TRSWn pin
*/
#define ATW_SYNRF_INTERSIL_EN (1<<20) /* if SELRF = 1, enables
* some signal used by the
* Intersil RF front-end?
* Undocumented.
*/
#define ATW_SYNRF_PHYRST (1<<18) /* if SELRF = 1, direct control of
* PHYRST# pin
*/
/* 1: force TXPE = RXPE = 1 if ATW_CMDR[27] = 0. */
#define ATW_C_SYNRF_RF2958PD ATW_SYNRF_PHYRST
#define ATW_BPLI_BP_MASK 0xffff0000 /* beacon interval in TU */
#define ATW_BPLI_LI_MASK 0xffff /* STA listen interval in
* beacon intervals
*/
#define ATW_C_CAP0_TIMLEN1 0xff000000 /* TIM table 1 len in bytes
* including TIM ID (XXX huh?)
*/
#define ATW_C_CAP0_TIMLEN0 0xff0000 /* TIM table 0 len in bytes,
* including TIM ID (XXX huh?)
*/
#define ATW_C_CAP0_CWMAX 0xf00 /* 1 <= CWMAX <= 5 fixes CW?
* 5 < CWMAX <= 9 sets max?
* 10?
* default 0
*/
#define ATW_CAP0_RCVDTIM (1<<4) /* receive every DTIM */
#define ATW_CAP0_CHN_MASK 0xf /* current DSSS channel */
#define ATW_CAP1_CAPI_MASK 0xffff0000 /* capability information */
#define ATW_CAP1_ATIMW_MASK 0xffff /* ATIM window in TU */
#define ATW_RMD_ATIMST (1<<31) /* ATIM frame TX status */
#define ATW_RMD_CFP (1<<30) /* CFP indicator */
#define ATW_RMD_PCNT 0xfff0000 /* idle time between
* awake/ps mode, in seconds
*/
#define ATW_RMD_RMRD_MASK 0xffff /* max RX reception duration
* in us
*/
#define ATW_CFPP_CFPP 0xff000000 /* CFP unit DTIM */
#define ATW_CFPP_CFPMD 0xffff00 /* CFP max duration in TU */
#define ATW_CFPP_DTIMP 0xff /* DTIM period in beacon
* intervals
*/
#define ATW_TOFS0_USCNT_MASK 0x3f000000 /* number of system clocks
* in 1 microsecond.
* Depends PCI bus speed?
*/
#define ATW_C_TOFS0_TUCNT_MASK 0x7c00 /* PIFS (microseconds) */
#define ATW_TOFS0_TUCNT_MASK 0x3ff /* TU counter in microseconds */
/* TBD TOFS1 */
#define ATW_TOFS1_TSFTOFSR_MASK 0xff000000 /* RX TSFT offset in
* microseconds: RF+BBP
* latency
*/
#define ATW_TOFS1_TBTTPRE_MASK 0xffff00 /* prediction time, (next
* Nth TBTT - TBTTOFS) in
* microseconds (huh?). To
* match TSFT[25:10] (huh?).
*/
#define ATW_TBTTPRE_MASK 0x3fffc00
#define ATW_TOFS1_TBTTOFS_MASK 0xff /* wake-up time offset before
* TBTT in TU
*/
#define ATW_IFST_SLOT_MASK 0xf800000 /* SLOT time in us */
#define ATW_IFST_SIFS_MASK 0x7f8000 /* SIFS time in us */
#define ATW_IFST_DIFS_MASK 0x7e00 /* DIFS time in us */
#define ATW_IFST_EIFS_MASK 0x1ff /* EIFS time in us */
#define ATW_RSPT_MART_MASK 0xffff0000 /* max response time in us */
#define ATW_RSPT_MIRT_MASK 0xff00 /* min response time in us */
#define ATW_RSPT_TSFTOFST_MASK 0xff /* TX TSFT offset in us */
#define ATW_WEPCTL_WEPENABLE (1<<31) /* enable WEP engine */
#define ATW_WEPCTL_AUTOSWITCH (1<<30) /* auto-switch enable (huh?) */
#define ATW_WEPCTL_CURTBL (1<<29) /* current table in use */
#define ATW_WEPCTL_WR (1<<28) /* */
#define ATW_WEPCTL_RD (1<<27) /* */
#define ATW_WEPCTL_WEPRXBYP (1<<25) /* bypass WEP on RX */
#define ATW_WEPCTL_SHKEY (1<<24) /* 1: pass to host if tbl
* lookup fails, 0: use
* shared-key
*/
#define ATW_WEPCTL_UNKNOWN0 (1<<23) /* has something to do with
* revision 0x20. Possibly
* selects a different WEP
* table.
*/
#define ATW_WEPCTL_TBLADD_MASK 0x1ff /* add to table */
/* set these bits in the second byte of a SRAM shared key record to affect
* the use and interpretation of the key in the record.
*/
#define ATW_WEP_ENABLED (1<<7)
#define ATW_WEP_104BIT (1<<6)
#define ATW_WESK_DATA_MASK 0xffff /* data */
#define ATW_WEPCNT_WIEC_MASK 0xffff /* WEP ICV error count */
#define ATW_MACTEST_FORCE_IV (1<<23)
#define ATW_MACTEST_FORCE_KEYID (1<<22)
#define ATW_MACTEST_KEYID_MASK 0x300000
#define ATW_MACTEST_MMI_USETXCLK (1<<11)
/* Function Event/Status registers */
#define ATW_FER_INTR (1<<15) /* interrupt: set regardless of mask */
#define ATW_FER_GWAKE (1<<4) /* general wake-up: set regardless of mask */
#define ATW_FEMR_INTR_EN (1<<15) /* enable INTA# */
#define ATW_FEMR_WAKEUP_EN (1<<14) /* enable wake-up */
#define ATW_FEMR_GWAKE_EN (1<<4) /* enable general wake-up */
#define ATW_FPSR_INTR_STATUS (1<<15) /* interrupt status */
#define ATW_FPSR_WAKEUP_STATUS (1<<4) /* CSTSCHG state */
#define ATW_FFER_INTA_FORCE (1<<15) /* activate INTA (if not masked) */
#define ATW_FFER_GWAKE_FORCE (1<<4) /* activate CSTSCHG (if not masked) */
/* Serial EEPROM offsets */
#define ATW_SR_CLASS_CODE (0x00/2)
#define ATW_SR_FORMAT_VERSION (0x02/2)
#define ATW_SR_MAJOR_MASK 0xff
#define ATW_SR_MINOR_MASK 0xff00
#define ATW_SR_MAC00 (0x08/2) /* CSR21 */
#define ATW_SR_MAC01 (0x0A/2) /* CSR21/22 */
#define ATW_SR_MAC10 (0x0C/2) /* CSR22 */
#define ATW_SR_CSR20 (0x16/2)
#define ATW_SR_ANT_MASK 0x1c00
#define ATW_SR_PWRSCALE_MASK 0x300
#define ATW_SR_CLKSAVE_MASK 0xc0
#define ATW_SR_RFTYPE_MASK 0x38
#define ATW_SR_BBPTYPE_MASK 0x7
#define ATW_SR_CR28_CR03 (0x18/2)
#define ATW_SR_CR28_MASK 0xff00
#define ATW_SR_CR03_MASK 0xff
#define ATW_SR_CTRY_CR29 (0x1A/2)
#define ATW_SR_CTRY_MASK 0xff00 /* country code */
#define COUNTRY_FCC 0
#define COUNTRY_IC 1
#define COUNTRY_ETSI 2
#define COUNTRY_SPAIN 3
#define COUNTRY_FRANCE 4
#define COUNTRY_MMK 5
#define COUNTRY_MMK2 6
#define ATW_SR_CR29_MASK 0xff
#define ATW_SR_PCI_DEVICE (0x20/2) /* CR0 */
#define ATW_SR_PCI_VENDOR (0x22/2) /* CR0 */
#define ATW_SR_SUB_DEVICE (0x24/2) /* CR11 */
#define ATW_SR_SUB_VENDOR (0x26/2) /* CR11 */
#define ATW_SR_CR15 (0x28/2)
#define ATW_SR_LOCISPTR (0x2A/2) /* CR10 */
#define ATW_SR_HICISPTR (0x2C/2) /* CR10 */
#define ATW_SR_CSR18 (0x2E/2)
#define ATW_SR_D0_D1_PWR (0x40/2) /* CR49 */
#define ATW_SR_D2_D3_PWR (0x42/2) /* CR49 */
#define ATW_SR_CIS_WORDS (0x52/2)
/* CR17 of RFMD RF3000 BBP: returns TWO channels */
#define ATW_SR_TXPOWER(chnl) (0x54/2 + ((chnl) - 1)/2)
/* CR20 of RFMD RF3000 BBP: returns TWO channels */
#define ATW_SR_LPF_CUTOFF(chnl) (0x62/2 + ((chnl) - 1)/2)
/* CR21 of RFMD RF3000 BBP: returns TWO channels */
#define ATW_SR_LNA_GS_THRESH(chnl) (0x70/2 + ((chnl) - 1)/2)
#define ATW_SR_CHECKSUM (0x7e/2) /* for data 0x00-0x7d */
#define ATW_SR_CIS (0x80/2) /* Cardbus CIS */
/* Tx descriptor */
struct atw_txdesc {
u_int32_t at_ctl;
#define at_stat at_ctl
u_int32_t at_flags;
u_int32_t at_buf1;
u_int32_t at_buf2;
};
#define ATW_TXCTL_OWN (1<<31) /* 1: ready to transmit */
#define ATW_TXCTL_DONE (1<<30) /* 0: not processed */
#define ATW_TXCTL_TXDR_MASK 0xff00000 /* TX data rate (?) */
#define ATW_TXCTL_TL_MASK 0xfffff /* retry limit, 0 - 255 */
#define ATW_TXSTAT_OWN ATW_TXCTL_OWN /* 0: not for transmission */
#define ATW_TXSTAT_DONE ATW_TXCTL_DONE /* 1: been processed */
#define ATW_TXSTAT_ES (1<<29) /* 0: TX successful */
#define ATW_TXSTAT_TLT (1<<28) /* TX lifetime expired */
#define ATW_TXSTAT_TRT (1<<27) /* TX retry limit expired */
#define ATW_TXSTAT_TUF (1<<26) /* TX under-run error */
#define ATW_TXSTAT_TRO (1<<25) /* TX over-run error */
#define ATW_TXSTAT_SOFBR (1<<24) /* packet size != buffer size
* (?)
*/
#define ATW_TXSTAT_ARC_MASK 0xfff /* accumulated retry count */
#define ATW_TXFLAG_IC (1<<31) /* interrupt on completion */
#define ATW_TXFLAG_LS (1<<30) /* packet's last descriptor */
#define ATW_TXFLAG_FS (1<<29) /* packet's first descriptor */
#define ATW_TXFLAG_TER (1<<25) /* end of ring */
#define ATW_TXFLAG_TCH (1<<24) /* at_buf2 is 2nd chain */
#define ATW_TXFLAG_TBS2_MASK 0xfff000 /* at_buf2 byte count */
#define ATW_TXFLAG_TBS1_MASK 0xfff /* at_buf1 byte count */
/* Rx descriptor */
struct atw_rxdesc {
u_int32_t ar_stat;
u_int32_t ar_ctl;
u_int32_t ar_buf1;
u_int32_t ar_buf2;
};
#define ar_rssi ar_ctl
#define ATW_RXCTL_RER (1<<25) /* end of ring */
#define ATW_RXCTL_RCH (1<<24) /* ar_buf2 is 2nd chain */
#define ATW_RXCTL_RBS2_MASK 0xfff000 /* ar_buf2 byte count */
#define ATW_RXCTL_RBS1_MASK 0xfff /* ar_buf1 byte count */
#define ATW_RXSTAT_OWN (1<<31) /* 1: NIC may fill descriptor */
#define ATW_RXSTAT_ES (1<<30) /* error summary, 0 on
* success
*/
#define ATW_RXSTAT_SQL (1<<29) /* has signal quality (?) */
#define ATW_RXSTAT_DE (1<<28) /* descriptor error---packet is
* truncated. last descriptor
* only
*/
#define ATW_RXSTAT_FS (1<<27) /* packet's first descriptor */
#define ATW_RXSTAT_LS (1<<26) /* packet's last descriptor */
#define ATW_RXSTAT_PCF (1<<25) /* received during CFP */
#define ATW_RXSTAT_SFDE (1<<24) /* PLCP SFD error */
#define ATW_RXSTAT_SIGE (1<<23) /* PLCP signal error */
#define ATW_RXSTAT_CRC16E (1<<22) /* PLCP CRC16 error */
#define ATW_RXSTAT_RXTOE (1<<21) /* RX time-out, last descriptor
* only.
*/
#define ATW_RXSTAT_CRC32E (1<<20) /* CRC32 error */
#define ATW_RXSTAT_ICVE (1<<19) /* WEP ICV error */
#define ATW_RXSTAT_DA1 (1<<17) /* DA bit 1, admin'd address */
#define ATW_RXSTAT_DA0 (1<<16) /* DA bit 0, group address */
#define ATW_RXSTAT_RXDR_MASK 0xf000 /* RX data rate */
#define ATW_RXSTAT_FL_MASK 0xfff /* RX frame length, last
* descriptor only
*/
/* Static RAM (contains WEP keys, beacon content). Addresses and size
* are in 16-bit words.
*/
#define ATW_SRAM_ADDR_INDIVL_KEY 0x0
#define ATW_SRAM_ADDR_SHARED_KEY (0x160 * 2)
#define ATW_SRAM_ADDR_SSID (0x180 * 2)
#define ATW_SRAM_ADDR_SUPRATES (0x191 * 2)
#define ATW_SRAM_MAXSIZE (0x200 * 2)
#define ATW_SRAM_A_SIZE ATW_SRAM_MAXSIZE
#define ATW_SRAM_B_SIZE (0x1c0 * 2)
Reference in New Issue View Git Blame Copy Permalink