have got the following:
Back out the changes in the previous revision. Function-like macros
were replaced by compound statements that work in less contexts.
Unoformize idempotency #ifdef.
Restore the simple leap year calculation as a macro and document it so
that it doesn't become complicated again. The simple version works
for all leap years covered by 32-bit time_t's. The complicated version
doesn't work for all leap years covered by 64-bit time_t's since among
other reasons, the solar system is not stable for long enough.
Fix declarations.
Nuke spinwait().
"gcc -Wstrict-prototypes" doesn't emit warnings about them.
Write each min/max functions on a single line so that the similarity and
triviality of the functions is more obvious.
Put the quad min/max functions in the correct place (aphabetical order).
The u_quad min/max functions are missing. Only 3 or 4 of the min/max
functions are actually used. sys/socketvar.h ``should use "lmin" but
it doesn't exist now''. lmin does exist now, but isn't used. Since we
depend on gcc for `inline', perhaps we should depend on it for __typeof
and function-expressions and use only macros min() and max() that work
for any types (I'm not sure how to handle mixed types).
actually used.
Remove "#ifdef __GNUC__" around some __dead* declarations. __dead* is
harmless if __GNUC__ is not defined.
Uniformize idempotency #ifdef.
This code is mostly taken from the 1.1 port (which was in turn taken from
Dave Mills's kern.tar.Z example). A few significant differences:
1) ntp_gettime() is now a MIB variable rather than a system call. A few
fiddles are done in libc to make it behave the same.
2) mono_time does not participate in the PLL adjustments.
3) A new interface has been defined (in <machine/clock.h>) for doing
possibly machine-dependent things around the time of the clock update.
This is used in Pentium kernels to disable interrupts, set `time', and
reset the CPU cycle counter as quickly as possible to avoid jitter in
microtime(). Measurements show an apparent resolution of a bit more than
8.14usec, which is reasonable given system-call overhead.
is used instead of /usr/lib
io.c: add #include <machine/cpufunc.h> as instructed by David Greenman to
avoid inb/outb linking errors.
NOTE: I just discovered that if GNUC is not used the inline functions will not be expanded from the include file and real inb/outb functions would
be needed.
when the drive had been left on a cylinder > 67 after kernel boot. The
most common case for this is booting a kernel that is located on
the inner cylinders of a floppy.
Also removed all occurences of spinwait(), replaced by DELAY.
Nuked a return line saying nothing, this might make Bruce happy 8^)
Submitted by: partially by Bruce Evans
date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.
New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track
Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now
Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()
Reviewed by:
Submitted by:
Obtained from:
arrange for that directory to get created by mtree. Also, process secure
directory after all the others, because the programs there may overlay
ones installed from the main part of the tree.
Remove the unnecessary inclusion of disklabel.h in cd9660_vfsops.c so
that I don't have to worry about the latter when changing disklabel.h.
Supply prototypes for some functions that were implicitly declared and
fix the resulting warnings and errors (timevals were punned to timespecs).
Removed inb function since it's more correctly in pio.h
Copied write_eflags and read_eflags over from npx.c
(Some changes to the macros suggested by Bruce were not made at this
time since his suggestions probably apply to all the macros and
these inlined/macro definitions need a lot of cleaning up at some
point in the future.)
Reviewed by: Bruce
Fix from Bruce Evans. There were missing sets of parantheses:
1. The checks for the standard data selectors were botched, so %ss == 0
and probably %cs == 0 were allowed. A fix is enclosed. The checks
for the standard selectors could be omitted without losing anything
since the standard selectors pass the valid_ldt_sel() tests.
320x200 256col VGA. This is nessesary for the iBCS stuff to work right.
(And we get the benefit of more video modes). Uses the videocard BIOS
to optain mode tables.
Added a "green" saver, switches off the syncs for "green" monitors.
Reviewed by:
Submitted by:
Obtained from:
don't hard-code netisr values in icu.s, but rather, use an array of
function pointers and set them all up in machdep.c for statically-linked
protocol families. (This will eventually be done differently.)
