#
# Maybe an alternate xntpd configuration for NSS#17
#

#
# precision is supported, but you don't really need it.  The code
# will determine a precision from the kernel's value of _hz which
# is fine.  Note you shouldn't claim too good a precision on a
# Unix machine even if the clock carries a lot of bits, since
# precision also depends on things like I/O delays and scheduling
# latencies, which Unix machines control poorly.  If you claim better
# than -6 or -7 it will make the anti-hop aperture tighter than is
# reasonable for a Unix machine.
#
#precision -7

#
# peers are ncarfuzz.ucar.edu umd1.umd.edu dcn5.udel.edu fuzz.sdsc.edu
# syntax is  peer addr [ key 1-15 ] [ version 1_or_2 ]
#

peer 128.116.64.3	# ncarfuzz.ucar.edu
peer 128.8.10.1		# umd1.umd.edu
peer 128.4.0.5		# dcn5.udel.edu
peer 192.12.207.1	# fuzz.sdsc.edu

#
# Drift file.  Put this in a directory which the daemon can write to.
# No symbolic links allowed, either, since the daemon updates the file
# by creating a temporary in the same directory and then rename()'ing
# it to the file.
#
# This is a nice feature.  Once you've got the drift computed it hardly
# ever takes more than an hour or so to resync after a restart.
#
driftfile /etc/ntp.drift

#
# The server statement causes polling to be done in client mode rather
# than symmetric active.  It is an alternative to the peer command
# above.  Which you use depends on what you want to achieve.  Usually
# it doesn't matter.  Syntax is:
#
#server 128.100.49.1 key 4 version 1

#
# The broadcast statement tells it to start broadcasting time out one
# of its interfaces.  Syntax is
#
#broadcast 128.100.49.255 # [ key n ] [ version n ]

#
# broadcastclient tells the daemon whether it should attempt to sync
# to broadcasts or not.  Defaults to `no'.
#
#broadcastclient yes # or no

#
# broadcastdelay configures in a default round-trip delay to use for
# broadcast time.  It may poll to improve this estimate.
#
#broadcastdelay 0.0095		# in seconds

#
# authenticate configures us into strict authentication mode (or not).
#
#authenticate yes	# or no.  Default is no

#
# authdelay is the time it takes to do an NTP encryption on this host.
# The current routine is pretty fast.
#
#authdelay 0.000340	# in seconds

#
# trustedkey are used when authenticate is on.  We only trust (and sync to)
# peers who know these keys.
#
#trustedkey 1 3 4 8

#
# monitor turns on the monitoring facility.  See xntpdc's monlist command.
# This shows a lot of neat stuff, but I'm not fussy about the implementation.
# Uses up to 20Kb of memory at run time.  You could try this.
#
#monitor yes		# or no.  Default is no

#
# keys points at the file which holds the authentication keys.
#
#keys /etc/ntp.keys

#
# requestkey indicates which key is to be used for validating
# runtime reconfiguration requests.  If this isn't defined, or the
# key isn't in the keys file, you can't do runtime reconfiguration.
# controlkey indicates which key is to be used for validating
# mode 6 write variables commands.  If this isn't defined you can't
# do it.  The only thing the latter is used for is to set leap second
# warnings on machines with radio clocks.
#
#requestkey 65535
#controlkey 65534

#
# restrict places restrictions on the punters.  This is implemented as
# a sorted address-and-mask list, with each entry including a set of
# flags which define what a host matching the entry *can't* do (the sort
# also saves CPU time searching the table since it needn't be searched
# to the end).  The last match in the table defines what the host does.
# The default entry, which everyone matches, is first, most specific
# matches are later in the table.  The flags are:
#
# ignore	- ignore all traffic from host
# noserve	- don't give host any time (but let him make queries?)
# notrust	- give host time, let him make queries, but don't sync to him
# noquery	- host can have time, but not make queries
# nomodify	- allow the host to make queries except those which are
#		  actually run-time configuration commands.
# notrap	- don't allow matching hosts to set traps.  If noquery is
#		  set this isn't needed
# lowpriotrap	- if this guy sets a trap make it easy to delete
# ntpport	- a different kind of flag.  Makes matches for this entry
#		  possible only if the source port is 123.
#
# To understand this better, take a look at xntpdc's reslist command when the
# server is running.  This usually prints in the sorted order.
#
# This should match the NSS 17 stuff.  Default mask is all ones.

restrict default ignore		# ignore almost everyone

#
# These guys can be served time and make non-modifying queries
#
restrict 129.140.0.0 mask 255.255.0.0 notrust nomodify
restrict 35.1.1.42 notrust nomodify

#
# Rest of 35.1.1 gets to look but not touch
#
restrict 35.1.1.0 mask 255.255.255.0 noserve nomodify

#
# modifications can be made from local NSS only
#
restrict 129.140.17.0 mask 255.255.255.0 notrust
restrict 127.0.0.1 notrust

#
# take time from the following peers, but don't let them peek or modify
#
restrict 128.116.64.3 noquery
restrict 128.8.10.1 noquery
restrict 128.4.0.5 noquery
restrict 192.12.207.1 noquery