ken 44638d924c Revamp camcontrol(8) fwdownload support and add the opcodes subcommand. ... The significant changes and bugs fixed here are: 1. Fixed a bug in the progress display code: When the user's filename is too big, or his terminal width is too small, the progress code could wind up using a negative number for the length of the "stars" that it uses to indicate progress. This negative value was assigned to an unsigned variable, resulting in a very large positive value. The result is that we wound up writing garbage from memory to the user's terminal. With an 80 column terminal, a file name length of more than 35 characters would generate this problem. To address this, we now set a minimum progress bar length, and truncate the user's file name as needed. This has been tested with large filenames and small terminals, and at least produces reasonable results. If the terminal is too narrow, the progress display takes up an additional line with each update, but this is more user friendly than writing garbage to the tty. 2. SATA drives connected via a SATA controller didn't have SCSI Inquiry data populated in struct cam_device. This meant that the code in fw_get_vendor() in fwdownload.c would try to match a zero-length vendor ID, and so return the first entry in the vendor table. (Which used to be HITACHI.) Fixed by grabbing identify data, passing the identify buffer into fw_get_vendor(), and matching against the model name. 3. SATA drives connected via a SAS controller do have Inquiry data populated. The table included a couple of entries -- "ATA ST" and "ATA HDS", intended to handle Seagate and Hitachi SATA drives attached via a SAS controller. SCSI to ATA translation layers use a vendor ID of "ATA" (which is standard), and then the model name from the ATA identify data as the SCSI product name when they are returning data on SATA disks. The cam_strmatch code will match the first part of the string (because the length it is given is the length of the vendor, "ATA"), and return 0 (i.e. a match). So all SATA drives attached to a SAS controller would be programmed using the Seagate method (WRITE BUFFER mode 7) of SCSI firmware downloading. 4. Issue #2 above covered up a bug in fw_download_img() -- if the maximum packet size in the vendor table was 0, it tried to default to a packet size of 32K. But then it didn't actually succeed in doing that, because it set the packet size to the value that was in the vendor table (0). Now that we actually have ATA attached drives fall use the VENDOR_ATA case, we need a reasonable default packet size. So this is fixed to properly set the default packet size. 5. Add support for downloading firmware to IBM LTO drives, and add a firmware file validation method to make sure that the firmware file matches the drive type. IBM tape drives include a Load ID and RU name in their vendor-specific VPD page 0x3. Those should match the IDs in the header of the firmware file to insure that the proper firmware file is loaded. 6. This also adds a new -q option to the camcontrol fwdownload subcommand to suppress informational output. When -q is used in combination with -y, the firmware upgrade will happen without prompting and without output except if an error condition occurs. 7. Re-add support for printing out SCSI inquiry information when asking the user to confirm that they want to download firmware, and add printing of ATA Identify data if it is a SATA disk. This was removed in r237281 when support for flashing ATA disks was added. 8. Add a new camcontrol(8) "opcodes" subcommand, and use the underlying code to get recommended timeout values for drive firmware downloads. Many SCSI devices support the REPORT SUPPORTED OPERATION CODES command, and some support the optional timeout descriptor that specifies nominal and recommended timeouts for the commands supported by the device. The new camcontrol opcodes subcommand allows displaying all opcodes supported by a drive, information about which fields in a SCSI CDB are actually used by a given SCSI device, and the nominal and recommended timeout values for each command. Since firmware downloads can take a long time in some devices, and the time varies greatly between different types of devices, take advantage of the infrastructure used by the camcontrol opcodes subcommand to determine the best timeout to use for the WRITE BUFFER command in SCSI device firmware downloads. If the device recommends a timeout, it is likely to be more accurate than the default 50 second timeout used by the firmware download code. If the user specifies a timeout, it will override the default or device recommended timeout. If the device doesn't support timeout descriptors, we fall back to the default. 9. Instead of downloading firmware to SATA drives behind a SAS controller using WRITE BUFFER, use the SCSI ATA PASS-THROUGH command to compose an ATA DOWNLOAD MICROCODE command and it to the drive. The previous version of this code attempted to send a SCSI WRITE BUFFER command to SATA drives behind a SAS controller. Although that is part of the SAT-3 spec, it doesn't work with the parameters used with LSI controllers at least. 10.Add a new mechanism for making common ATA passthrough and ATA-behind-SCSI passthrough commands. The existing camcontrol(8) ATA command mechanism checks the device type on every command executed. That works fine for individual commands, but is cumbersome for things like a firmware download that send a number of commands. The fwdownload code detects the device type up front, and then sends the appropriate commands. 11.In simulation mode (-s), if the user specifies the -v flag, print out the SCSI CDB or ATA registers that would be sent to the drive. This will aid in debugging any firmware download issues. sbin/camcontrol/fwdownload.c: Add a device type to the fw_vendor structure, so that we can specify different download methods for different devices from the same vendor. In this case, IBM hard drives (from when they still made hard drives) and tape drives. Add a tur_status field to the fw_vendor structure so that we can specify whether the drive to be upgraded should be ready, not ready, or whether it doesn't matter. Add the corresponding capability in fw_download_img(). Add comments describing each of the vendor table fields. Add HGST and SmrtStor to the supported SCSI vendors list. In fw_get_vendor(), look at ATA identify data if we have a SATA device to try to identify what the drive vendor is. Add IBM firmware file validation. This gets VPD page 0x3, and compares the Load ID and RU name in the page to the values included in the header. The validation code will refuse to load a firmware file if the values don't match. This does allow the user to attempt a downgrade; whether or not it succeeds will likely depend on the drive settings. Add a -q option, and disable all informative output (progress bars, etc.) when this is enabled. Re-add the inquiry in the confirmation dialog so the user has a better idea of which device he is talking to. Add support for displaying ATA identify data. Don't automatically disable confirmation in simulation (-s) mode. This allows the user to see the inquiry or identify data in the dialog, and see exactly what they would see when the command actually runs. Also, in simulation mode, if the user specifies the -v flag, print out the SCSI CDB or ATA registers that would be sent to the drive. This will aid in debugging any firmware download issues. Add a timeout field and timeout type to the firmware download vendor table. This allows specifying a default timeout and allows specifying whether we should attempt to probe for a recommended timeout from the drive. Add a new fuction, fw_get_timeout(), that will determine which timeout to use for the WRITE BUFFER command. If the user specifies a timeout, we always use that. Otherwise, we will use the drive recommended timeout, if available, and fall back to the default when a drive recommended timeout isn't available. When we prompt the user, tell him what timeout we're going to use, and the source of the timeout. Revamp the way SATA devices are handled. In fwdownload(), use the new get_device_type() function to determine what kind of device we're talking to. Allow firmware downloads to any SATA device, but restrict SCSI downloads to known devices. (The latter is not a change in behavior.) Break out the "ready" check from fw_download_img() into a new subfunction, fw_check_device_ready(). This sends the appropriate command to the device in question -- a TEST UNIT READY or an IDENTIFY. The IDENTIFY for SATA devices a SAT layer is done using the SCSI ATA PASS-THROUGH command. Use the new build_ata_cmd() function to build either a SCSI or ATA I/O CCB to issue the DOWNLOAD MICROCODE command to SATA devices. build_ata_cmd() figures looks at the devtype argument and fills in the correct CCB type and CDB or ATA registers. Revamp the vendor table to remove the previous vendor-specific ATA entries and use a generic ATA vendor placeholder. We currently use the same method for all ATA drives, although we may have to add vendor-specific behavior once we test this with more drives. sbin/camcontrol/progress.c: In progress_draw(), make barlength a signed value so that we can easily detect a negative value. If barlength (the length of the progress bar) would wind up negative due to a small TTY width or a large filename, set the bar length to the new minimum (10 stars) and truncate the user's filename. We will truncate it down to 0 characters if necessary. Calculate a new prefix_len variable (user's filename length) and use it as the precision when printing the filename. sbin/camcontrol/camcontrol.c: Implement a new camcontrol(8) subcommand, "opcodes". The opcodes subcommand allows displaying the entire list of SCSI commands supported by a device, or details on an individual command. In either case, it can display nominal and recommended timeout values. Add the scsiopcodes() function, which calls the new scsigetopcodes() function to fetch opcode data from a drive. Add two new functions, scsiprintoneopcode() and scsiprintopcodes(), which print information about one opcode or all opcodes, respectively. Remove the get_disk_type() function. It is no longer used. Add a new function, dev_has_vpd_page(), that fetches the supported INQUIRY VPD list from a device and tells the caller whether the requested VPD page is available. Add a new function, get_device_type(), that returns a more precise device type than the old get_disk_type() function. The get_disk_type() function only distinguished between SCSI and ATA devices, and SATA devices behind a SCSI to ATA translation layer were considered to be "SCSI". get_device_type() offers a third type, CC_DT_ATA_BEHIND_SCSI. We need to know this to know whether to attempt to send ATA passthrough commands. If the device has the ATA Information VPD page (0x89), then it is an ATA device behind a SCSI to ATA translation layer. Remove the type argument from the fwdownload() subcommand. Add a new function, build_ata_cmd(), that will take one set of common arguments and build either a SCSI or ATA I/O CCB, depending on the device type passed in. sbin/camcontrol/camcontrol.h: Add a prototype for scsigetopcodes(). Add a new enumeration, camcontrol_devtype. Add prototypes for dev_has_vpd_page(), get_device_type() and build_ata_cmd(). Remove the type argument from the fwdownload() subcommand. sbin/camcontrol/camcontrol.8 Explain that the fwdownload subcommand will use the drive recommended timeout if available, and that the user can override the timeout. Document the new opcodes subcommand. Explain that we will attempt to download firmware to any SATA device. Document supported SCSI vendors, and models tested if known. Explain the commands used to download firmware for the three different drive and controller combinations. Document that the -v flag in simulation mode for the fwdownload subcommand will print out the SCSI CDBs or ATA registers that would be used. sys/cam/scsi/scsi_all.h: Add new bit definitions for the one opcode descriptor for the REPORT SUPPORTED OPCODES command. Add a function prototype for scsi_report_supported_opcodes(). sys/cam/scsi/scsi_all.c: Add a new CDB building function, scsi_report_supported_opcodes(). Sponsored by: Spectra Logic MFC after: 1 week		2015-08-20 16:07:51 +00:00
..
attrib.c
camcontrol.8	Revamp camcontrol(8) fwdownload support and add the opcodes subcommand.	2015-08-20 16:07:51 +00:00
camcontrol.c	Revamp camcontrol(8) fwdownload support and add the opcodes subcommand.	2015-08-20 16:07:51 +00:00
camcontrol.h	Revamp camcontrol(8) fwdownload support and add the opcodes subcommand.	2015-08-20 16:07:51 +00:00
fwdownload.c	Revamp camcontrol(8) fwdownload support and add the opcodes subcommand.	2015-08-20 16:07:51 +00:00
Makefile
Makefile.depend
modeedit.c
persist.c
progress.c	Revamp camcontrol(8) fwdownload support and add the opcodes subcommand.	2015-08-20 16:07:51 +00:00
progress.h
util.c