mirror of
https://git.hardenedbsd.org/hardenedbsd/HardenedBSD.git
synced 2024-11-18 00:21:25 +01:00
53c9f6c0c4
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
545 lines
14 KiB
Plaintext
545 lines
14 KiB
Plaintext
.\" manual page [] for ppp 0.94 beta2 + alpha
|
|
.\" $Id: ppp.8,v 1.1.1.1 1995/01/31 06:29:58 amurai Exp $
|
|
.\" SH section heading
|
|
.\" SS subsection heading
|
|
.\" LP paragraph
|
|
.\" IP indented paragraph
|
|
.\" TP hanging label
|
|
.TH PPP 8
|
|
.SH NAME
|
|
ppp \- Point to Point Protocol (aka iijppp)
|
|
.SH SYNOPSIS
|
|
.B ppp
|
|
[
|
|
.I -auto | -direct -dedicated
|
|
] [
|
|
.I system
|
|
]
|
|
.SH DESCRIPTION
|
|
.LP
|
|
This is user process \fIPPP\fR software package. Normally, \fIPPP\fR
|
|
is implemented as a part of kernel and hard to debug and/or modify its
|
|
behavior. However, in this implementation, \fIPPP\fR is implemented as
|
|
a user process with the help of tunnel device driver.
|
|
.LP
|
|
|
|
.SH Major Features
|
|
|
|
.TP 2
|
|
o Provide interactive user interface. Using its command mode, user can
|
|
easily enter commands to establish the connection with the peer, check
|
|
the status of connection, and close the connection. And now, all
|
|
functions has password protected if describe your hostname/password in
|
|
secret file or exist secret file itself.
|
|
|
|
.TP 2
|
|
o Supports both of manual and automatic dialing. Interactive mode has
|
|
``term'' command which enables you to talk to your modem
|
|
directory. When your modem is connected to the peer, and it starts to
|
|
speak \fIPPP\fR, \fIPPP\fR software detects it and turns into packet
|
|
mode automatically. Once you have convinced how to connect with the
|
|
peer, you can write chat script to define necessary dialing and login
|
|
procedure for later convenience.
|
|
|
|
.TP 2
|
|
o Supports on-demand dialup capability. By using auto mode, \fIPPP\fR
|
|
program will act as a daemon and wait for the packet send to the peer.
|
|
Once packet is found, daemon automatically dials and establish the
|
|
connection.
|
|
|
|
.TP 2
|
|
o
|
|
Can act as server which accept incoming \fIPPP\fR connection.
|
|
|
|
.TP 2
|
|
o
|
|
Supports PAP and CHAP authentification.
|
|
|
|
.TP 2
|
|
o
|
|
Supports Proxy Arp.
|
|
|
|
.TP 2
|
|
o Supports packet filtering. User can define four kinds of filters;
|
|
ifilter for incoming packet, ofilter for outgoing packet, dfilter to
|
|
define dialing trigger packet and afilter to keep alive a connection
|
|
by trigger packet.
|
|
|
|
.TP 2
|
|
o Tunnel driver supports bpf. That is, user can use tcpdump to check
|
|
packet flow over the \fIPPP\fR link.
|
|
|
|
.TP 2
|
|
o
|
|
Supports \fIPPP\fR over TCP capability.
|
|
|
|
.TP 2
|
|
o
|
|
Supports IETF draft Predictor-1 compression.
|
|
|
|
.TP 2
|
|
o Runs under BSDI-1.1 and FreeBSD-1.1. Patch for NeXTSTEP 3.2 is also
|
|
available on the net.
|
|
|
|
.SH MANUAL DIALING
|
|
|
|
% ppp
|
|
User Process PPP written by Toshiharu OHNO.
|
|
-- If you write your hostname and password in ppp.secret,
|
|
you can't do anything even quit command --
|
|
ppp on tama> quit
|
|
what ?
|
|
ppp on tama> pass <password>
|
|
-- You can specify modem and device name using following commands.
|
|
ppp ON tama> set line /dev/cua01
|
|
ppp ON tama> set speed 38400
|
|
ppp ON tama> set parity even
|
|
ppp ON tama> show modem
|
|
-- Modem related parameters are shown in here
|
|
ppp ON tama>
|
|
-- Use term command to talk with your modem
|
|
ppp ON tama> term
|
|
at
|
|
OK
|
|
atdt123456
|
|
CONNECT
|
|
|
|
login: ppp
|
|
Password:
|
|
-- PPP started in remote side ---
|
|
|
|
-- When peer start to speak PPP, the program will detect it
|
|
-- automatically and back to command mode.
|
|
ppp on tama>
|
|
\fBPPP\fR>
|
|
|
|
-- NOW, you are get connected !! Note that prompt has changed to
|
|
-- capital letters
|
|
PPP ON tama> show lcp
|
|
|
|
-- You'll see LCP status --
|
|
|
|
PPP ON tama> show ipcp
|
|
|
|
-- You'll see IPCP status --
|
|
-- At this point, your machine has host route to the peer.
|
|
-- If your want to add default route entry, then enter
|
|
|
|
PPP ON tama> add 0 0 HISADDR
|
|
|
|
-- Here string `HISADDR' represents IP address of connected peer.
|
|
|
|
PPP ON tama>
|
|
-- Use applications (i.e. ping, telnet, ftp) in other windows
|
|
|
|
PPP ON tama> show log
|
|
|
|
-- Gives you some logging messages
|
|
|
|
PPP ON tama> close
|
|
|
|
-- Connection is closed, and modem will be hanged.
|
|
|
|
ppp ON tama> quit
|
|
%
|
|
.LP
|
|
|
|
.SH AUTOMATIC DIALING
|
|
|
|
.LP
|
|
To use automatic dialing, you must prepare Dial and Login chat script.
|
|
See example definition found in ppp.conf.sample (Format of ppp.conf is
|
|
pretty simple.)
|
|
|
|
.TP 2
|
|
o
|
|
Each line contains one command, label or comment.
|
|
|
|
.TP 2
|
|
o
|
|
Line stating with # is treated as a comment line.
|
|
|
|
.TP 2
|
|
o
|
|
Label name has to start from first column and should be followed by colon (:).
|
|
|
|
.TP 2
|
|
o
|
|
Command line must contains space or tab at first column.
|
|
|
|
.LP
|
|
If ppp.conf is ready, specify destination label name when you invoke
|
|
ppp. Commands associated with destination label is executed when ppp
|
|
command is invoked. Note that commands associated with ``default''
|
|
label is ALWAYS executed.
|
|
|
|
Once connection is made, you'll find that prompt is changed to
|
|
|
|
capital \fIPPP\fR>.
|
|
|
|
% ppp pm2
|
|
...
|
|
ppp ON tama> dial
|
|
dial OK!
|
|
login OK!
|
|
PPP ON tama>
|
|
|
|
If ppp.linkup file is available, its contents are executed when
|
|
\fIPPP\fR link is connected. See example which add default route.
|
|
The string HISADDR matches with IP address of connected peer.
|
|
|
|
|
|
.SH DAIL ON DEMAND
|
|
|
|
.LP
|
|
To play with demand dialing, you must use -auto option. Also, you
|
|
must specify destination label with proper setup in ppp.conf. It must
|
|
contain ``ifaddr'' command to define peer's IP address. (refer
|
|
/etc/ppp/ppp.conf.sample)
|
|
|
|
|
|
% ppp -auto pm2demand
|
|
...
|
|
%
|
|
|
|
.LP
|
|
When -auto is specified, \fIPPP\fR program works as a daemon. But,
|
|
you are still able to use command features to check its behavior.
|
|
|
|
|
|
% telnet localhost 3000
|
|
...
|
|
PPP on tama> show ipcp
|
|
....
|
|
|
|
.LP
|
|
Each ppp has associated port number, which is computed as "3000 +
|
|
tunnel_device_number". If 3000 is not good base number, edit defs.h.
|
|
When packet toward to remote network is detected, \fIPPP\fR will take
|
|
dialing action and try to connect with the peer. If dialing is failed,
|
|
program will wait for 30 seconds. Once this hold time expired, another
|
|
trigger packet cause dialing action. Note that automatic re-dialing is
|
|
NOT implemented.
|
|
|
|
|
|
To terminate program, use
|
|
|
|
PPP on tama> close
|
|
\fBppp\fR> quit all
|
|
|
|
.LP
|
|
Simple ``quit'' command will terminates telnet connection, but \fIPPP\fR program itself is not terminated. You must use ``quit all'' to terminate the program running as daemon.
|
|
.LP
|
|
|
|
.SH PACKET FILTERING
|
|
|
|
.LP
|
|
This implementation supports packet filtering. There are three filters; ifilter, ofilter and dfilter. Here's some basics.
|
|
.LP
|
|
|
|
.TP 2
|
|
o
|
|
Filter definition has next syntax.
|
|
|
|
set filter-name rule-no action [src_addr/src_width] [dst_addr/dst_width]
|
|
[proto [src [lt|eq|gt] port ] [dst [lt|eq|gt] port] [estab]
|
|
|
|
a) filter-name should be ifilter, ofilter or dfiler.
|
|
|
|
b) There are two actions permit and deny. If given packet is matched
|
|
against the rule, action is taken immediately.
|
|
|
|
c) src_width and dst_width works like a netmask to represent address range.
|
|
|
|
d) proto must be one of icmp, udp or tcp.
|
|
|
|
.TP 2
|
|
o
|
|
Each filter can hold upto 20 rules. Rule number starts from 0. Entire rule set is not effective until rule 0 is defined.
|
|
|
|
.TP 2
|
|
o
|
|
If no rule is matched with a packet, that packet will be discarded (blocked).
|
|
|
|
.TP 2
|
|
o
|
|
Use ``set filer-name -1'' to flush all rules.
|
|
|
|
.LP
|
|
See /etc/ppp/ppp.conf.filter.example
|
|
.LP
|
|
|
|
.SH RECEIVE INCOMING PPP CONNECTION
|
|
|
|
.LP
|
|
To receive incoming \fIPPP\fR connection request, follow next steps.
|
|
.LP
|
|
|
|
a) Prepare bidir entry in your /etc/gettytab
|
|
|
|
bidir.38400:\
|
|
:bi:ap:hf:tc=38400-baud:
|
|
|
|
b) Edit /etc/ttys to enable getty on the port where modem is attached.
|
|
|
|
cua00 "/usr/libexec/getty stdir.38400" dialup on
|
|
|
|
Don't forget to send HUP signal to init process.
|
|
|
|
# kill -HUP 1
|
|
|
|
c) Prepare account for incoming user.
|
|
|
|
ppp:*:21:0:PPP Login User:/home/ppp:/usr/local/bin/ppplogin
|
|
|
|
d) Create /usr/local/bin/ppplogin file with next contents.
|
|
|
|
#!/bin/sh
|
|
/usr/local/bin/ppp -direct
|
|
|
|
You can specify label name for further control.
|
|
|
|
.LP
|
|
Direct mode (-direct) lets \fIPPP\fR to work with standard in and out. Again, you can telnet to 3000 to get command mode control.
|
|
.LP
|
|
|
|
.SH SETTING IDLE TIMER
|
|
|
|
.LP
|
|
To check/set idletimer, use ``show timeout'' and ``set timeout'' command.
|
|
.LP
|
|
|
|
Ex. ppp> set timeout 600
|
|
|
|
.LP
|
|
Timeout period is measured in secs and default value is 180 or 3 min. To disable idle timer function, use ``set timeout 0''.
|
|
.LP
|
|
|
|
.LP
|
|
In -auto mode, idle timeout cause \fIPPP\fR session closed. However, \fIPPP\fR program itself is keep running. Another trigger packet cause dialing action.
|
|
.LP
|
|
|
|
.SH Predictor-1 compression
|
|
|
|
.LP
|
|
This version supports CCP and Predictor type 1 compression based on current IETF-draft specs. As a default behavior, \fIPPP\fR will propose to use (or willing to accept) this capability and use it if peer agrees (or requests).
|
|
.LP
|
|
|
|
.LP
|
|
To disable CCP/predictor function completely, use ``disable pred'' and ``deny pred'' command.
|
|
.LP
|
|
|
|
.SH Controlling IP address
|
|
|
|
.LP
|
|
\fIPPP\fR uses IPCP to negotiate IP addresses. Each side of node
|
|
informs IP address that willing to use to the peer, and if requested
|
|
IP address is acceptable, \fIPPP\fR returns ACK to
|
|
requester. Otherwise, \fIPPP\fR returns NAK to suggest the peer to use
|
|
different IP address. When both side of nodes agrees to accept the
|
|
received request (and send ACK), IPCP is reached to open state and
|
|
network level connection is established.
|
|
|
|
|
|
.LP
|
|
To control, this IPCP behavior, this implementation has ``set
|
|
ifaddr'' to define MY and HIS IP address.
|
|
|
|
|
|
.TP3
|
|
ifaddr src_addr dst_addr
|
|
|
|
.LP
|
|
Where, src_addr is the IP address that my side is willing to use, and
|
|
dst_addr is the IP address which his side should use.
|
|
.LP
|
|
|
|
.TP3
|
|
ifaddr 192.244.177.38 192.244.177.2
|
|
|
|
For example, above specification means
|
|
|
|
.TP
|
|
o I strongly want to use 192.244.177.38 as my side. I'll disagree when
|
|
peer suggest me to use other addresses.
|
|
|
|
.TP 2
|
|
o I strongly insists peer to use 192.244.177.2 as his side address. I
|
|
don't permit him to use any IP address but 192.244.177.2. When peer
|
|
request other IP address, I always suggest him to use 192.244.177.2.
|
|
|
|
.LP
|
|
This is all right, when each side has pre-determined IP address.
|
|
However, it is often the case one side is acting as a server which
|
|
controls IP address and the other side should obey the direction from
|
|
him. In order to allow more flexible behavior, `ifaddr' command
|
|
allows user to specify IP address more loosely.
|
|
|
|
|
|
.TP 2
|
|
ifaddr 192.244.177.38/24 192.244.177.2/20
|
|
|
|
Number followed by slash (/) represents number of bits significant in
|
|
IP address. That is, this example means
|
|
|
|
.TP 2
|
|
o I'd like to use 192.244.177.38 as my side address, if it is
|
|
possible. But I also accept any IP address between 192.244.177.0 and
|
|
192.244.177.255.
|
|
|
|
.TP 2
|
|
o I'd like to make him to use 192.244.177.2 as his side address. But
|
|
I also permit him to use any IP address between 192.244.176.0 and
|
|
192.244.191.255.
|
|
|
|
Notes:
|
|
|
|
.TP 2
|
|
o As you may have already noticed, 192.244.177.2 is equivalent to say
|
|
192.244.177.2/32.
|
|
|
|
.TP 2
|
|
o As an exception, 0 is equivalent to 0.0.0.0/0. Means, I have no idea
|
|
about IP address and obey what he says.
|
|
|
|
.TP 2
|
|
o 192.244.177.2/0 means that I'll accept/permit any IP address but
|
|
I'll try to insist to use 192.244.177.2 at first.
|
|
|
|
.SH Connecting with service provider
|
|
|
|
.LP
|
|
1) Describe provider's phone number in DialScript. Use ``set dial'' or
|
|
``set phone'' command.
|
|
|
|
2) Describle login procedure in LoginScript. Use ``set login'' command.
|
|
|
|
.TP
|
|
3) Use ``set ifaddr'' command to define IP address.
|
|
|
|
o If you know what IP address provider uses, then use it as his address.
|
|
|
|
o If provider has assigned particular IP address for you, then use it
|
|
as my address.
|
|
|
|
o If provider assigns your address dynamically, use 0 as my address.
|
|
|
|
o If you have no info on IP addresses, then try
|
|
|
|
set ifaddr 0 0
|
|
.TP 2
|
|
4) If provider request you to use PAP/CHAP auth method,
|
|
add next lines into your ppp.conf.
|
|
|
|
.TP 3
|
|
.B enable pap (or enable chap)
|
|
.TP 3
|
|
.B disable chap (or disable pap)
|
|
.TP 3
|
|
.B set authname MyName
|
|
.TP 3
|
|
.B set authkey MyPassword
|
|
.TP 3
|
|
|
|
.LP
|
|
Please refer /etc/ppp/ppp.conf.iij for some real examples.
|
|
.LP
|
|
|
|
.SH Logging facility
|
|
|
|
.LP
|
|
\fI\fIPPP\fR\fR is able to generate following level log info as
|
|
/var/log/ppp.log
|
|
|
|
|
|
.TP
|
|
.B Phase
|
|
Phase transition log output
|
|
.TP
|
|
.B Chat
|
|
Generate Chat script trace log
|
|
.TP
|
|
.B LQM
|
|
Generate LQR report
|
|
.TP
|
|
.B LCP
|
|
Generate LCP/IPCP packet trace
|
|
.TP
|
|
.B TCP/IP
|
|
Dump TCP/IP packet
|
|
.TP
|
|
.B HDLC
|
|
Dump HDLC packet in hex
|
|
.TP
|
|
.B Async
|
|
Dump async level packet in hex
|
|
|
|
.LP
|
|
``set debug'' command allows you to set logging output level, and
|
|
multiple levels can be specified. Default is equivalent to ``set
|
|
debug phase lcp''.
|
|
|
|
.SH For more details
|
|
|
|
.TP 2
|
|
o
|
|
Please read Japanese doc for complete explanation.
|
|
Well, it is not useful for non-japanese readers,
|
|
but examples in the document may help you to guess.
|
|
|
|
.TP 2
|
|
o
|
|
Please read example configuration files.
|
|
|
|
.TP 2
|
|
o
|
|
Use ``help'', ``show ?'' and ``set ?'' command.
|
|
|
|
.TP 2
|
|
o
|
|
NetBSD and BSDI-1.0 has been supported in previous release,
|
|
but no longer supported in this release.
|
|
Please contact to author if you need old driver code.
|
|
|
|
.SH FILES
|
|
.LP
|
|
\fIPPP\fR may refers three files, ppp.conf, ppp.linkup and ppp.secret.
|
|
These files are placed in /etc/ppp, but user can create his own files
|
|
under HOME directory as .ppp.conf,.ppp.linkup and .ppp.secret.the ppp
|
|
always try to consult to user's personal setup first.
|
|
|
|
.TP
|
|
.B $HOME/ppp/.ppp.[conf|linkup|secret]
|
|
User depend configuration files.
|
|
|
|
.TP
|
|
.B /etc/ppp/ppp.conf
|
|
System default configuration file.
|
|
|
|
.TP
|
|
.B /etc/ppp/ppp.secret
|
|
A authorization file for each system.
|
|
|
|
.TP
|
|
.B /etc/ppp/ppp.linkup
|
|
A checking file when
|
|
.I ppp
|
|
establishes network level connection.
|
|
|
|
.TP
|
|
.B /var/log/ppp.log
|
|
Logging and debug information file.
|
|
|
|
.TP
|
|
.B /var/spool/lock/Lck..*
|
|
tty port locking file.
|
|
|
|
.SH BUGS
|
|
|
|
.SH HISTORY
|
|
This programm has deliverd into core since FreeBSD-2.1 by Atsushi
|
|
Murai (amurai@spec.co.jp).
|
|
|
|
.SH AUTHORS
|
|
Toshiharu OHNO (tony-o@iij.ad.jp)
|