HardenedBSD/sbin/ifconfig/ifconfig.8

.\" Copyright (c) 1983, 1991, 1993
.\"	The Regents of the University of California.  All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\" 3. All advertising materials mentioning features or use of this software
.\"    must display the following acknowledgement:
.\"	This product includes software developed by the University of
.\"	California, Berkeley and its contributors.
.\" 4. Neither the name of the University nor the names of its contributors
.\"    may be used to endorse or promote products derived from this software
.\"    without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED.  IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\"     From: @(#)ifconfig.8	8.3 (Berkeley) 1/5/94
.\"	$Id: ifconfig.8,v 1.7 1996/02/13 17:30:26 wollman Exp $
.\"
.Dd February 13, 1996
.Dt IFCONFIG 8
.Os BSD 4.2
.Sh NAME
.Nm ifconfig
.Nd configure network interface parameters
.Sh SYNOPSIS
.Nm ifconfig
.Ar interface address_family
.Oo
.Ar address
.Op Ar dest_address
.Oc
.Op Ar parameters
.Nm ifconfig
.Ar interface
.Op Ar protocol_family
.Nm ifconfig
.Ar -a
.Nm ifconfig
.Ar -au
.Nm ifconfig
.Ar -ad
.Sh DESCRIPTION
.Nm Ifconfig
is used to assign an address
to a network interface and/or configure
network interface parameters.
.Nm Ifconfig
must be used at boot time to define the network address
of each interface present on a machine; it may also be used at
a later time to redefine an interface's address
or other operating parameters.
.Pp
Available operands for
.Nm ifconfig:
.Bl -tag -width Ds
.It Ar Address
For the
.Tn DARPA-Internet
family,
the address is either a host name present in the host name data
base, 
.Xr hosts 5 ,
or a
.Tn DARPA
Internet address expressed in the Internet standard
.Dq dot notation .
.\" For the Xerox Network Systems(tm) family,
.\" addresses are 
.\" .Ar net:a.b.c.d.e.f ,
.\" where
.\" .Ar net
.\" is the assigned network number (in decimal),
.\" and each of the six bytes of the host number,
.\" .Ar a
.\" through
.\" .Ar f ,
.\" are specified in hexadecimal.
.\" The host number may be omitted on 10Mb/s Ethernet interfaces,
.\" which use the hardware physical address,
.\" and on interfaces other than the first.
.\" For the
.\" .Tn ISO
.\" family, addresses are specified as a long hexadecimal string,
.\" as in the Xerox family.  However, two consecutive dots imply a zero
.\" byte, and the dots are optional, if the user wishes to (carefully)
.\" count out long strings of digits in network byte order.
.It Ar address_family
Specifies the
.Ar address family
which affects interpretation of the remaining parameters.
Since an interface can receive transmissions in differing protocols
with different naming schemes, specifying the address family is recommended.
The address or protocol families currently
supported are
.Dq inet ,
.Dq atalk ,
.\" .Dq iso ,
and
.Dq ipx .
.\" and
.\" .Dq ns .
.It Ar Interface
The
.Ar interface
parameter is a string of the form
.Dq name unit ,
for example,
.Dq en0 
.El
.Pp
The following parameters may be set with 
.Nm ifconfig :
.Bl -tag -width dest_addressxx
.It Cm alias
Establish an additional network address for this interface.
This is sometimes useful when changing network numbers, and
one wishes to accept packets addressed to the old interface.
.It Cm arp
Enable the use of the Address Resolution Protocol in mapping
between network level addresses and link level addresses (default).
This is currently implemented for mapping between
.Tn DARPA
Internet
addresses and 10Mb/s Ethernet addresses.
.It Fl arp
Disable the use of the Address Resolution Protocol.
.It Cm broadcast
(Inet only)
Specify the address to use to represent broadcasts to the
network.
The default broadcast address is the address with a host part of all 1's.
.It Cm debug
Enable driver dependent debugging code; usually, this turns on
extra console error logging.
.It Fl debug
Disable driver dependent debugging code.
.It Cm delete
Remove the network address specified.
This would be used if you incorrectly specified an alias, or it
was no longer needed.
If you have incorrectly set an NS address having the side effect
of specifying the host portion, removing all NS addresses will
allow you to respecify the host portion.
.It Cm dest_address
Specify the address of the correspondent on the other end
of a point to point link.
.It Cm down
Mark an interface ``down''.  When an interface is
marked ``down'', the system will not attempt to
transmit messages through that interface. 
If possible, the interface will be reset to disable reception as well.
This action does not automatically disable routes using the interface.
.\" .It Cm ipdst
.\" This is used to specify an Internet host who is willing to receive
.\" ip packets encapsulating NS packets bound for a remote network.
.\" An apparent point to point link is constructed, and
.\" the address specified will be taken as the NS address and network
.\" of the destination.
.\" IP encapsulation of
.\" .Tn CLNP
.\" packets is done differently.
.It Cm metric Ar n
Set the routing metric of the interface to
.Ar n ,
default 0.
The routing metric is used by the routing protocol
.Pq Xr routed 8 .
Higher metrics have the effect of making a route
less favorable; metrics are counted as addition hops
to the destination network or host.
.It Cm mtu Ar n
Set the maximum transmission unit of the interface to
.Ar n ,
default is interface specific.
The mtu is used to limit the size of packets that are transmitted on an
interface.
Not all interfaces support setting the mtu, and some interfaces have
range restrictions.
.It Cm netmask Ar mask
.\" (Inet and ISO)
(Inet only)
Specify how much of the address to reserve for subdividing
networks into sub-networks.
The mask includes the network part of the local address
and the subnet part, which is taken from the host field of the address.
The mask can be specified as a single hexadecimal number
with a leading 0x, with a dot-notation Internet address,
or with a pseudo-network name listed in the network table
.Xr networks 5 .
The mask contains 1's for the bit positions in the 32-bit address
which are to be used for the network and subnet parts,
and 0's for the host part.
The mask should contain at least the standard network portion,
and the subnet field should be contiguous with the network
portion.
.\" see 
.\" Xr eon 5 .
.\" .It Cm nsellength Ar n
.\" .Pf ( Tn ISO
.\" only)
.\" This specifies a trailing number of bytes for a received
.\" .Tn NSAP
.\" used for local identification, the remaining leading part of which is
.\" taken to be the
.\" .Tn NET
.\" (Network Entity Title).
.\" The default value is 1, which is conformant to US
.\" .Tn GOSIP .
.\" When an ISO address is set in an ifconfig command,
.\" it is really the
.\" .Tn NSAP
.\" which is being specified.
.\" For example, in
.\" .Tn US GOSIP ,
.\" 20 hex digits should be
.\" specified in the
.\" .Tn ISO NSAP
.\" to be assigned to the interface.
.\" There is some evidence that a number different from 1 may be useful
.\" for
.\" .Tn AFI
.\" 37 type addresses.
.It Cm link[0-2]
Enable special processing of the link level of the interface.
These three options are interface specific in actual effect, however,
they are in general used to select special modes of operation. An example
of this is to enable SLIP compression.
.It Fl link[0-2]
Disable special processing at the link level with the specified interface.
.It Cm up
Mark an interface ``up''. 
This may be used to enable an interface after an ``ifconfig down.''
It happens automatically when setting the first address on an interface.
If the interface was reset when previously marked down,
the hardware will be re-initialized.
.El
.Pp
.Pp
The
.Nm ifconfig
.Fl a
command
displays information on all interfaces.  When followed by a configuration
parameter, it will also set the configuration on all interfaces.
.Pp
.Nm Ifconfig
.Fl au
is similar to
.Nm ifconfig
.Fl a ,
except it only affects interfaces that are currently marked as up.
Similarly,
.Nm ifconfig
.Fl ad
affects only interfaces that are marked down.
.Pp
The
.Nm
program
displays the current configuration for a network interface
when no optional parameters are supplied.
If a protocol family is specified,
.Nm ifconfig
will report only the details specific to that protocol family.
.Pp
Only the super-user may modify the configuration of a network interface.
.Sh DIAGNOSTICS
Messages indicating the specified interface does not exit, the
requested address is unknown, or the user is not privileged and
tried to alter an interface's configuration.
.Sh SEE ALSO
.Xr netstat 1 ,
.Xr netintro 4 ,
.Xr rc 8 ,
.Xr routed 8 ,
.\" .Xr eon 5
.Sh HISTORY
The
.Nm
command appeared in
.Bx 4.2 .