mirror of
https://git.hardenedbsd.org/hardenedbsd/HardenedBSD.git
synced 2024-12-30 15:38:06 +01:00
5326bef3de
This looks like it was developed offline, and is being spammed over the top of the existing. "That's fine by me! I dont really care how you do it, just get it in there..." said Jordan in a conversation a short while ago...
55 lines
2.9 KiB
Plaintext
55 lines
2.9 KiB
Plaintext
You can do network installations over 3 types of communications links:
|
|
|
|
Serial port: SLIP / PPP
|
|
Parallel port: PLIP (laplink cable)
|
|
Ethernet: A standard ethernet controller (includes some PCMCIA).
|
|
|
|
SLIP support is rather primitive and limited primarily to hard-wired
|
|
links, such as a serial cable running between a laptop computer and
|
|
another PC. The link must be hard-wired as the SLIP installation
|
|
doesn't currently offer a dialing capability; that facility is provided
|
|
with the PPP utility, which should be used in preference to SLIP
|
|
whenever possible. When you choose a serial port device, you'll
|
|
be given the option later to edit the slattach command before it's
|
|
run on the serial line. It is expected that you'll run slattach
|
|
(or some equivalent) on the other end of the link at this time and
|
|
bring up the line. FreeBSD will then install itself over the link
|
|
at speeds of up to 115.2K/baud (the recommended speed for a hardwired
|
|
cable).
|
|
|
|
If you're using a modem then PPP is almost certainly your only
|
|
choice. Make sure that you have your service provider's information
|
|
handy as you'll need to know it fairly early in the installation
|
|
process. You will need to know, at the minimum, your service
|
|
provider's IP address and possibly your own (though you can also leave
|
|
it blank and allow PPP to negotiate it with your ISP). You will also
|
|
need to know how to use the various "AT commands" to dial the ISP with
|
|
your particular brand of modem as the PPP dialer provides only a very
|
|
simple terminal emulator and has no "modem capabilities database".
|
|
|
|
If a hard-wired connection to another FreeBSD (2.0R or later) machine
|
|
is available, you might also consider installing over a "laplink"
|
|
parallel port cable. The data rate over the parallel port is much
|
|
higher than what is typically possible over a serial line with
|
|
speeds of up to 50k/sec.
|
|
|
|
Finally, for the fastest possible network installation, an ethernet
|
|
adaptor is always a good choice! FreeBSD supports most common PC
|
|
ethernet cards, a table of which is provided in the FreeBSD
|
|
Hardware Guide (see the Documentation menu on the boot floppy).
|
|
If you are using one of the supported PCMCIA ethernet cards, also be
|
|
sure that it's plugged in _before_ the laptop is powered on! FreeBSD
|
|
does not, unfortunately, currently support "hot insertion" of PCMCIA
|
|
cards.
|
|
|
|
You will also need to know your IP address on the network, the "netmask"
|
|
value for your address class, and the name of your machine.
|
|
Your system administrator can tell you which values to use for your
|
|
particular network setup. If you will be referring to other hosts by
|
|
name rather than IP address, you'll also need a name server and
|
|
possibly the address of a gateway (if you're using PPP, it's your
|
|
provider's IP address) to use in talking to it. If you do not know
|
|
the answers to all or most of these questions, then you should
|
|
really probably talk to your system administrator _first_ before
|
|
trying this type of installation!
|