>Category: bin
>Synopsis: SPAP request REJexted in stead of NAKed
>Confidential: no
>Severity: non-critical
>Priority: low
>Responsible: freebsd-bugs (FreeBSD bugs mailing list)
>State: open
>Class: sw-bug
>Submitter-Id: current-users
>Arrival-Date: Wed Jul 5 01:40:01 1995
>Originator: Dick van den Burg
>Organization:
>Release: FreeBSD 2.0.5-RELEASE i386
>Environment:
>Description:
When trying to connect with ppp to a Shiva Lanrover (version 3.2) the
authentication fails because the SPAP (Shiva Secure PAP) configuration
request the is sent by Shive is REJected by ppp in stead of NAKed.
Reviewed by: amurai@spec.c.jp and friends
Submitted by: burg@is.ge.com
might not be handled by the same FS as the directory (e.g. special device
files)...so it must be special-cased. This bug is seen when doing
"ln /dev/console /dev/foo" or equivilent and first appeared after I fixed
the argument order of VOP_LINK. YUCK! There really needs to be a way of
specifying what vp to use in the VCALL; doing this could fix the strategy
and bwrite special-cases, too.
complain about an 'illegal line count' becuase it's looking
at the wrong end pointer (ep) to detect any extra characters
after the NNN.
Submitted by: Rich Murphey <rich@freebsd.org>
This should probably get pulled into 2.0.6 and 2.1.0
constructors and destructors.
Add -lgcc_pic to LDADD for the shared library since C++ code uses stuff from
libgcc and we no longer have a shared libgcc. Should this be done by
CPLUSPLUSLIB?
- use pseudo-dma
- provide the same features and interface as sio
- support multiple boards
- fix bugs.
Some compile-time configuration constants are set to support higher
speeds and Cyclom-16Y's at a 30% relative cost in efficiency.
Cyclom-16Y support is untested.
form to do this than it is relying on individual subroutines (the logic
in epioctl is itself very minimal). Ideally, unnecessary splimp()'s should
now be removed if they exist; I'll leave this for a later date (a complete
code review of the driver needs to be done). Fixes a bug I noticed that
would show up when ifconfig'ing the interface down.
Strange as it sounds, it should map to YPERR_DOMAIN instead.
The YP_NODOM protocol error code is generally returned by ypserv when you
ask it for data from a domain that it doesn't support. By contrast,
the YPERR_NODOM error code means 'local domain name not set.'
Consequently, this incorrect mapping leads to yperr_string() generating
a very confusing error message. YPERR_DOMAIN says 'couldn't
bind to a server which serves this domain' which is much closer
to the truth.
platform, I discovered the following: if you use ypcat (or anything that
does a yp_all() for that matter) to dump out a map and then hit ^C before
it finishes, ypserv gets hit with a SIGPIPE and dies. (The ypall() service
is implemented using TCP.)
Fix: ignore SIGPIPEs.
optimizations I have been working on yet, but does bring in some bug fixes
and performance improvments that were easy to regression test:
Setup the data fifo threshold and bus off timing correctly for 27/284x cards.
Users of these adapters with fast periferals (greater than 5MB/s) will notice
a big performance difference. (Sometimes as large as going from 3.7->8.3MB/s).
Fix handling of the active target flags. Some of the outbs where missing
the base offset in the abort code. The abort code still needs lots of work.
Support 3940 controllers, but only with 16 SCBs for now. Eventually I'll
add support for all 255, but I need to find a tester for the code first since
we have to enable the cards external SRAM to do this.
Add Dan Eischen's serial eeprom reading facilities. This allows the 2940
adapters to pull additional information left over from SCSI-Select right out
out of the configuration seeprom.
If the BIOS is disabled on 274x controllers, reset all target parameters
to there defaults since you can't rely on what is stored in scratch ram.
Report motherboard controllers as such.
Stick the first SG address and count into the SCB data and count areas for
all transfers in preparation of a later sequencer optimization.
Keep track of which targets can are allowed to have the disconnection
priveledge since this will be handled by the kernel driver in the future.
If a target issues a message reject in response to a tagged message,
disable tagged queuing for that target. Some seagates say they can do
tagged queuing, but lie, and its a shame to have to disable tagged queuing
on all devices just because you have one that can't cope.
is needed for 3940 support.
Have tagged commands look to see if a target is "busy" with a non tagged
command before executing. This prevents overlapped tagged and non tagged
commands which can happen since request sense commands are not tagged.
bootparam_prot.x was changed for nfsv3 but bootparamd and callbootd
kept using the old version which fortunately failed at build time.
Copying hasn't been necessary since path handling was fixed in
rpcgen/rpc_main.c some time ago.
incorrect indents, a variety of poor coding practices such as comparing
pointers to constants ('0'), poor code structuring, etc, etc. This brings
the code up to the minimum standards for inclusion in FreeBSD.
2) Rewrote "bad_packet" code to be less buggy and more readable.
3) Removed a pile of goto's; the code is now somewhat less reminiscent
of a certain Italian pasta.
4) Changed all boolean returns of "0" and "1" to FALSE/TRUE.
- Use one sprintf() to put together the path to the map database instead
of strcat()s and strcpy()s.
- Make the 'error opening database' Perror() statement sane.
assigning an address to an interface automatically marks this
interface IFF_UP. The fix corrects this (and closes PR sys/577).
This is consistent with the way ethernet interfaces are being handled.
stream, such as a rsh or vi pipeline.
The error message is:
stty: TIOCGETD: Operation not supported
It's immediately obvious to the knowledgable hacker type, but not
exactly comforting to the user who's not native to unix. It's
especially confusing if there's a stty command in their .cshrc and
it's showing up on rsh output.
(Fixes PR #bin/573)
Submitted by: peter@haywire.dialix.com (Peter Wemm)
All cross reference labels start with name of the file that contains
them. A label for the top section level is simply the name of the
file (omitting the .sgml). Other references within the file append a
colon and onother name. For example, the label on the mailing list
section in the file eresources.sgml is eresources:mail. This gives
each file its own cross reference namespace.
1) Do dependencies.
2) Install all appropriate links to manual pages.
3) Install header file in `beforeinstall' like all the rest.
4) Install header file only if changed.
5) Install object files only if changed.
